Cwe23sp4mw2 Parts

Includes 12 screws.

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

A replacement 8-18 x 3/4 flanged pan-head screw used to secure panels, trim, and components. Restores proper fit and stops loose parts from rattling or shifting, helping appliances operate quietly and safely. What it does

• Fastens panels, brackets, trim pieces or assemblies that use an 8-18 thread screw
• Replaces missing or stripped screws that cause loose or vibrating parts
• Helps maintain proper alignment of panels and covers
• Prevents gaps that can allow movement or noise during operation

• One 8-18 x 3/4 flanged pan-head screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread the screw in by hand first, then snug; avoid over-tightening
• If underlying threads are damaged, replace the mating fastener or insert as needed

This condenser support is the replacement mounting bracket that holds the refrigerator condenser or condenser coil securely in place, helping maintain proper clearance and airflow for reliable cooling performance. What it does:

• Secures the condenser or condenser coil to the cabinet to prevent movement or vibration
• Maintains correct condenser positioning to support consistent airflow and heat dissipation
• Helps reduce rattling or noise caused by a loose condenser assembly
• Supports overall cooling reliability by keeping components aligned

• One condenser support bracket

• Installation requires basic hand tools; disconnect power before beginning any repair
• Handle sharp sheet-metal edges carefully to avoid cuts
• Reinstall any removed panels or fasteners to restore proper airflow paths

A replacement rubber mounting cushion that isolates and secures the refrigerator compressor to reduce vibration and noise. Restores proper compressor seating to help lower vibration transfer and prevent premature wear. What it does:

• Cushions the compressor to absorb vibration and reduce noise during operation
• Helps keep the compressor properly aligned and secured to the mounting bracket
• Can reduce rattling or buzzing that indicates worn or missing mounts
• Protects mounting hardware and body panels from metal-on-metal contact

• One compressor grommet

• Turn off power to the appliance and unplug before servicing
• Inspect surrounding mounts and hardware; replace any damaged fasteners
• Grommet installs between compressor and mounting bracket; reuse OEM orientation

This rubber grommet cushions and protects small appliance wires, hoses, or components where they pass through panels or openings. It helps prevent chafing and vibration wear for quieter, longer-lasting operation. What it does:

• Cushions wiring or tubing where it passes through sheet metal to prevent rubbing and damage
• Reduces vibration noise from loose fittings or contact points
• Holds harnesses or hoses in position to maintain proper routing
• Helps keep openings sealed against dust and debris around routed components

• Disconnect appliance power (and water if applicable) before replacing parts
• Remove the original grommet and install the new grommet in the same orientation; ensure the wire/hose seats fully in the grommet
• Inspect surrounding wiring, hoses, and mounting holes for damage and replace if needed
• Use only the specified replacement grommet; do not modify with adhesives or solvents unless manufacturer guidance allows

This center track screw cover caps the exposed screw on the center track assembly to protect the screw head and give the track a finished appearance. It helps reduce debris buildup and prevents accidental snags on the screw head. What it does:

• Covers and protects the center track screw head from dirt, moisture, and surface wear
• Helps maintain a smooth surface on the track to reduce snagging or catching
• Restores the OEM appearance where the original cap is missing or damaged
• Small replacement part used with center track assemblies and trim pieces

• One center track screw cover (cap)

• Designed for simple push- or snap-fit installation over the exposed screw head
• Remove power to the appliance before accessing internal trim or track areas, and follow manufacturer safety guidance
• If screw or track is damaged, inspect and replace the underlying hardware before installing the cap
• Handle small parts carefully to avoid loss during installation