We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.
By putting on the part. Read more
This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.
Ultimately is was discovered and caused by the blower wheel shaft opening was cracked and broken. Replaced blower fan wheel. Read more
This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:
I watched the repair video AppliancePartsPros.com had on each repair and followed the instructions. Read more
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
One of three coils, to get all three order 12001348
I ohm metered the sensors to determine which one was bad (open) Looked up the part on the parts drawing. Ordered part and had the dryer running 2 days later Read more
Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.
Fix a dryer that won't shut off or advance through cycles. This mechanical timer controls cycle progression and timed functions in your dryer.
Replaced the timer. Read more
Size: 8-32 x 1/4 inch.
Replaced switch assembly Read more
Dryer making rumbling noise or drying slowly? A worn blower wheel with a rounded center causes wobbling and poor airflow. Moderate DIY repair.
In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more
Usually ships within 4 - 14 days
Seals blower housing to prevent air leaks and lint escape. Replace when you notice lint buildup in your home or reduced drying efficiency. Confirm fit with your model number.
Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more
Lifter fin that mounts inside the rotating drum to tumble laundry. Replace if cracked, broken, or missing. Installs with screws for proper load movement.
Replaced with new Drum Baffles Read more
Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.
A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:
Used Google to research issues. We ordered a new motor and springs. Installed and washer running like new. Read more
Single screw used to secure panels, brackets, and internal components to the dryer frame. Replaces lost, stripped, or damaged fasteners during repairs.
At first i just bought the belt, started dryer and off came the belt, and yes it was in place,looking at the idler arm it had a lot off back and forth movement so i ordered the whole assembly but the spring which no one has.put it all together again but drum barely turned.. so back apart and belt was in place. took the idler spring out cut 4 loops off it re did the end so it would hook on idler arm.and that did the trick.runs like new. Read more