Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer not heating or shutting off early? The safety thermostat monitors temperature and cuts power when it gets too hot. Tests quickly with a multimeter.
Specs: 10 - 16 x .375
Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more
Replaced bulb and screen. Read more
The belts were very easy to change through the back of the machine. The heating element was a bit more involved. I basically had to disassemble the entire machine. The heating element is located on the front panel of the machine surrounding the door. You have to remove the rear panel, the top panel and loosen both side panels from the bottom pan, 6 screws. Then you slide the 2 sides and front panel (all still attached) a few inches forward so that you can access the screws that secure the side... Read more
Replaced bulb Read more
Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:
I have a Maytag washer that is over 30 years old and still runs like a top. When the siphon break got destroyed in our move, I was able to find a replacement kit that fixed our problem. I found a video on UTube that showed us just what to do. I'm delighted I didn't have to buy a new washer since the quality of new ones doesn't hold a candle to the quality of my Maytag. Read more
This small hardware washer serves as a spacer/bearing surface within appliance assemblies to distribute load and maintain proper clearance. Replacing a worn washer helps restore smooth operation and alignment of the affected control or mechanism. What it does:
This was my first ever self appliance repair. The videos provided by Appliance Parts Pros were excellent and gave me the confidence to do the work myself. My Maytag dryer model opened differently than the one in the videos. I had to remove the front panel and screwing in the paddle required reaching way back and working in a small space where I couldn't see what I was doing. It was uncomfortable but doable with a nut driver and a bit of elbow grease. The part fit perfectly and it looks good as... Read more
Cushions and guides the dryer drum for smooth rotation. Replace when worn, cracked, or causing excess vibration. Installs on drum support shaft.
This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.
Purchased timer and baffle, and my appliance repairman installed them. I could get the parts cheaper than he could from his supplier; he asked me for the Appliance Parts Pros website address! Read more
I had to replace the terminal block due to the 220 volt ark. A small fire at the bottom of the dryer caused the belt to partially burn. I had to replace it along with the 220 volt dryer cable. If the local hardware store would have taken the time to install the dryer with an additional 0.50 cent grommet, this could have been avoided. Thank you for sending the correct parts. This was the second time I had to use your service and I will continue to use it in the future. Read more
Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more
The nylon slides on the front felt seal were worn out, allowing the drum to sag in the front. This is where our clothing would get caught and scorch. I replaced the felt, rear bearing kit and while I was that far, I replaced the belt as it's very inexpensive. All done for less than 10% of a new dryer purchase. Read more
Secures wiring harness to prevent chafing and maintain safe wire routing in washers, dryers, and laundry appliances. Replace if loose or broken. Check your model for compatibility.
I ordered the gas valve coil kit and the thermostat heat control. I replaced the coils first and found that coils were the problem. Read more
By Frigidaire. Screen - 12-1/4" wide. Mounting frame included - 12-3/4" between mounting holes.
This adjustable leveling leg supports your dryer and allows you to level the appliance on uneven floors. It screws into the dryer's base and can be raised or lowered to eliminate rocking or vibration. Replace it when the leg is bent, stripped, or won't adjust properly, causing your dryer to be unstable or noisy.
Ordered new feet that fit unit. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.