Du920pf Parts

Small mounting clip that secures interior panels and trim pieces in your dishwasher. Replaces clips that are cracked, broken, or missing to restore fit.

This pivot clip allows the dishwasher tines to fold down flat, creating space for loading large plates and cookware in the lower rack. It provides the hinge mechanism that lets you adjust the tine configuration based on your loading needs. Replace this clip if tines won't stay folded down, pop back up during washing, or if the pivot mechanism is broken.

Fix spray arms that wobble, fall off, or don't rotate properly with this dishwasher spray arm lock support. Simple snap-in installation takes 10 minutes.

This is a small rolling caster wheel designed to support and allow easy movement of the appliance during installation or repositioning. It mounts to the underside of the unit to enable smooth transport across floors. Replace this wheel if it is broken, seized, or missing, which can make the appliance difficult to move and may cause floor damage.

Secures the cup shelf to your dishwasher's upper rack. Replace this clip if it's broken, cracked, or missing to keep your cup holder stable and secure.

Dishwasher making loud grinding noise or not draining? This pump and motor assembly circulates wash water and drains the tub. Moderate DIY repair.

Protective rubber bumper for dishwasher dishrack. Installs on the outer front edge of the lower rack. Replace if cracked, broken, or missing.

Size: 8-32 x 1/4 inch.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Wire harness elbow connector for dishwashers. Replaces damaged, cracked, or broken electrical connectors that route power between components.

This dishrack replaces a damaged, rusted, or warped rack to restore smooth loading and secure support for dishes. A solid rack keeps items upright for better spray coverage, cleaner results, and helps prevent rust transfer and chipping.

• Holds and organizes plates, bowls, and cookware for proper spacing and spray access
• Provides stable support to reduce tipping and breakage during wash cycles
• Replaces racks with rust, broken wires, or bent/missing tines
• Can help resolve issues like rust marks on dishes and loading difficulties

• Disconnect power at the breaker before servicing
• Open the door; slide the old rack out—on some models, release rack stops to remove
• Transfer any reusable accessories from the old rack to the new rack if applicable
• Wear cut-resistant gloves; set the new rack on the rails and verify smooth movement and proper door closure

This replacement dishrack restores secure loading and proper spacing so wash water reaches every item. Replacing a bent or rusty rack helps prevent tipped dishes and marks from flaking rust, and keeps loading/unloading smooth when the rack rollers are intact.

• Holds plates, bowls, and cups in place during wash and rinse cycles
• Maintains spacing for spray coverage and drying airflow
• Rolls in and out along the rails when paired with functional rack rollers
• Common symptoms include broken or bent tines, flaking coating or rust, items tipping, or difficulty sliding the rack

• Disconnect power to the dishwasher before servicing
• Open the door, pull the rack forward, release rack stops/end caps if present, and slide the old rack off the rails
• Transfer any reusable accessories from the old rack to the new rack as required by your model
• Slide the new rack onto the rails, reinstall rack stops, and verify smooth travel before running a cycle

Seals the pump housing to prevent water leaking from the tub onto the motor. Replace if you see leaks around the circulation pump area. Confirm fit by model.

Seal gasket for dishwasher inlet base assembly. Replace if you notice leaks, moisture buildup, or debris entering internal components. Confirm fit.

Dishwasher won't drain or overflows? A missing or worn check ball can cause backflow issues. This small part maintains one-way water flow in the valve.