Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer won't start or cycle selection not working? This control board assembly manages all electronic functions. Moderate DIY repair, requires console access.
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replace idler, motor mounting clamp and lock Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Dryer not heating? A failed igniter won't light the gas burner. This glow-bar igniter heats up to ignite gas during each cycle. Moderate DIY repair.
Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
If your dryer runs too hot, won't heat properly, or shuts off unexpectedly, the inlet thermistor may have failed. This sensor monitors incoming air temperature.
Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Dryer not heating properly or overheating? The thermistor monitors temperature and signals the control board. Common DIY repair, takes 15-30 minutes.
Replacement door glass for dryer doors. Provides a clear viewing window to monitor laundry during cycles. Order when glass is cracked, broken, or missing.
Dryer won't start, stops mid-cycle, or displays error codes? The main control board regulates all dryer functions. Moderate difficulty repair.
Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.