We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Most orders arrive by Wednesday, November 25
Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replace idler, motor mounting clamp and lock Read more
Dryer not heating? A failed igniter won't light the gas burner. This glow-bar igniter heats up to ignite gas during each cycle. Moderate DIY repair.
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.
Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.
If your dryer runs too hot, won't heat properly, or shuts off unexpectedly, the inlet thermistor may have failed. This sensor monitors incoming air temperature.
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Dryer not heating properly or overheating? The thermistor monitors temperature and signals the control board. Common DIY repair, takes 15-30 minutes.
Replacement door glass for dryer doors. Provides a clear viewing window to monitor laundry during cycles. Order when glass is cracked, broken, or missing.
Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.
Seals your dryer door to prevent heat loss and improve drying efficiency. Replace if stretched, collapsed, or air is escaping. Verify fit with model.
Replaced the seal Read more
Dryer won't start, stops mid-cycle, or displays error codes? The main control board regulates all dryer functions. Moderate difficulty repair.
First got a new part, which was giving me a different error (E92) the error was clearing on reset, but reset was needed before every cycle, called appliancepartspros and they got me a replacement part, which was working without any problems once installed. Read more
Dryer not starting or power cutting out? A melted or corroded terminal block disrupts power flow. This 3-terminal block restores secure connections. DIY-friendly repair.
While checking a no heat issue with dryer noticed that terminal block was melted due to loose connections, replaced terminal block with new and replaced heating element. Read more