Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix unresponsive buttons or blank displays with this user interface control board. Restores keypad function and display readings on your laundry center.
Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Secures and protects your dryer's lint screen for effective lint capture. Replace if cracked, broken, or loose to maintain airflow and efficiency.
The Main Board is an OEM part for Frigidaire electric dryers. As the central component that controls all dryer functions, the main board is critical for proper operation. It processes signals from thermostats and sensors to advance the drying cycle, monitor heat levels, and ensure safety features are enabled.
Causes of a bad main board can include failure over time due to heat exposure, moisture incursion leading to shorts or corrosion, or faulty programming of the microchip.
Symptoms of a bad main board include:
This OEM replacement is also compatible with Electrolux, Amana, Roper, Gibson, Kelvinator, and Kenmore models. Replace yours now to restore full dryer functionality before further issues arise.
Replaced the main circuit board. Read more
Dryer won't heat? A faulty gas burner assembly prevents proper flame and ignition. This part restores heat for efficient drying. DIY repair in 1-2 hours.
Went to youtube and found out what was the cause. Replaced the parts that said might be the issue, Dryer working perfectly. All done in about 1/12 hrs Read more
If your dryer runs too hot, won't heat properly, or shuts off unexpectedly, the inlet thermistor may have failed. This sensor monitors incoming air temperature.
Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.
If your dryer won't power on, stops after a few seconds, or shows error codes, the main control board may have failed. Moderate DIY repair project.
The Main Board is an OEM component specifically designed for Frigidaire electric clothes dryers. As the central processing unit, it regulates drying cycles, temperature controls, and diagnostic monitoring.
Symptoms of a faulty main board include:
Causes of a bad main board can include general wear from years of continuous operation and exposure to high heat. Rigorous drying cycles and potential impacts can deteriorate delicate electronic circuits over time.
This OEM Frigidaire part is also compatible with Electrolux, Crosley, and some Kenmore dryers. Replacing restores reliable functions like moisture detection and thermal protections to preserve efficient, safe drying performance as intended by the manufacturer. Maintaining control boards prevents disruptive issues.
Dryer not heating properly or overheating? The thermistor monitors temperature and signals the control board. Common DIY repair, takes 15-30 minutes.
Burner orifice that meters gas flow to your dryer's burner. Replace if clogged, damaged, or wrong size for fuel type during LP/natural gas conversion.
Dryer won't start, stops mid-cycle, or displays error codes? The main control board regulates all dryer functions. Moderate difficulty repair.
Dryer not starting or power cutting out? A melted or corroded terminal block disrupts power flow. This 3-terminal block restores secure connections. DIY-friendly repair.
While checking a no heat issue with dryer noticed that terminal block was melted due to loose connections, replaced terminal block with new and replaced heating element. Read more
Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.