Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement drum support roller wheel assembly for dryers. Installs on bulkhead to support and guide drum rotation. Replace when worn, cracked, or loose.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Fixes steam cycle not working or water not entering drum during steam cycles. Controls water flow into dryer. Moderate DIY repair for steam dryers.
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
Converting your dryer from natural gas to propane? This LP conversion kit includes calibrated orifices for proper fuel flow. DIY-friendly install.
Removing cabinet panels to access burner was the major challenge since every one seems to be different. This one, two screws at back allowed top to raise and be removed, Two more screws at front and two cables disconnected removed control panel. The door panel was not quite as obvious, The two screws at top sides and two at very bottom edge were removed. Then by trial, I removed screws around door edge until panel was loose. I removed a couple extra; but the whole door and panel lifted off.... Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.
Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.
Dryer won't start or runs but won't heat? The main control board regulates all drying functions. Moderate DIY repair with proper harness installation.
The Lint Filter Kit is an OEM component specifically designed for Frigidaire clothes dryers. This kit includes both the main lint filter that collects lint and debris during the drying cycle, as well as the installed mesh screen filter component. These filters play a crucial role in protecting the dryer by trapping lint and preventing clogs in the ventilation system.
Causes of a bad lint filter kit include excessive lint buildup that blocks airflow, physical damage to the mesh screen or filter housing, or missing components.
Symptoms of a bad lint filter kit include:
This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Well, my husband fixed it. First of all, the parts came super quick! He then had to take out the installed dryness sensor unit and install a new one with the new filter that prevents lint from getting into the exhaust motor. When the exhaust motor is filled with lint, it makes a thumping sound. So, before he put in the new parts, he had to disassemble the dryer to clean out the exhaust motor from the compacted lint. Then, put it all back together again. Thankfully, there are good videos on... Read more
Fix a dryer that won't shut off automatically or has temperature control issues. This thermistor sensor monitors heat levels for proper cycle operation.
I replaced the thermostat. The bearing on the motor was getting loose, so I changed the motor to. The repair took about 2 hours. There are some good re[air videos on the parts web site. Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Dryer won't start or cycle selection not working? This control board assembly manages all electronic functions. Moderate DIY repair, requires console access.
Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.
Replaced all sensors, limiters, thermistors, thermostat. Works great now. Read more
Fix E51 error codes and unresponsive controls with this dryer main control board. Controls temperature, timer, heating, and motor functions.
Replaced control board and changed the sensors while I was in there. Fixed! Read more
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replace idler, motor mounting clamp and lock Read more