Eimed60jiw Parts

This replacement seal restores a tight barrier between mating surfaces in your appliance, helping contain air, moisture, and heat where intended for reliable performance and efficiency.

• Forms a tight barrier to help prevent leaks, drafts, or heat loss
• Replaces a cracked, torn, flattened, or missing seal
• Can help address issues like moisture around an opening, temperature fluctuations, or rattling/vibration from a poor fit
• Restores proper closure and performance when the original seal is worn

• Disconnect power and shut off water/gas before service
• Note the routing/orientation of the original seal; take photos for reference
• Clean the channel/mating surfaces thoroughly; remove old adhesive and debris
• Seat the new seal fully without stretching; close and test for proper fit and contact

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

This terminal block provides the mounting point and secure electrical connection for the appliance power leads. Replacing a damaged or corroded terminal block restores a solid power connection and reduces arcing or intermittent power. What it does:

• Provides a secure connection between the incoming power cord and the appliance wiring
• Holds and isolates power terminals to prevent shorting and arcing
• Commonly fails when terminals are burned, corroded, loose, or when wires heat at the connection
• Symptoms of a failing terminal include loss of power, intermittent power, visible burn marks or arcing at the connection, and melted or discolored insulation

• One terminal block

• Always disconnect power at the breaker or unplug the appliance before servicing
• Tighten mounting screws and terminal screws securely; inspect and replace any damaged wire insulation

This replacement pulley guides the drive belt so the drum or tub turns smoothly and reliably. A worn pulley can squeal, shred belts, or stop the load from tumbling or spinning.

• Guides the drive belt and helps transfer motor power to the drum/tub
• A seized or damaged pulley can cause the drum/tub not to turn or to stall
• Inspect for cracks, wobble, or rough bearings during diagnosis

• Disconnect power before servicing; if working on a gas dryer, also shut off the gas supply. For washers, turn off water.
• Access the belt path; release belt tension and remove the old pulley.
• Install the new pulley and route the belt correctly; rotate by hand to confirm smooth tracking.
• Inspect and replace a worn drive belt or related belt-drive components while open.

This OEM fastener replaces a worn, stripped, or missing nut to securely hold components in place inside compatible laundry appliances. Restores proper clamping force to reduce vibration, rattling, and loosening during operation. What it does:

• Secures a mating bolt or stud to keep brackets, panels, or rotating parts firmly mounted
• Restores proper tension after the original nut is lost, corroded, or damaged
• Helps address symptoms like excessive vibration, rattling, or loose assemblies
• Maintains a tight connection in high-vibration environments when properly tightened

• 1 nut

• Disconnect power (and water to a washer) before servicing
• Support the component being fastened; hold the bolt head while loosening/tightening the nut
• Start threads by hand to avoid cross-threading; tighten to manufacturer guidance
• Replace any damaged bolts or hardware it mates with for a secure repair

This hinge secures and lets a refrigerator door pivot smoothly, restoring proper door alignment and sealing for consistent cooling. Replace a worn or bent hinge to fix sagging doors and uneven gaps that stop the door from closing correctly. What it does

• Provides the pivot point that lets the refrigerator door open and close
• Restores proper door alignment and a tight seal to help maintain interior temperature
• Stops sagging or tilted doors that catch or don't latch fully
• Replaces damaged, bent, or worn hinge hardware that causes noisy or uneven movement

• Disconnect power and empty the door before starting to reduce weight and risk of tipping
• Support the door during removal and installation to prevent damage or personal injury
• Use correct fasteners and torque to factory specification; do not overtighten
• Check striker/closer components and gasket condition

This drum mixing vane is a molded paddle that helps lift and tumble clothes inside the dryer drum for more even drying and reduced tangling. It's a direct-replacement style piece that restores proper fabric movement and airflow. What it does:

• Resets the drum's internal lift so garments rotate and tumble evenly during the dry cycle
• Helps prevent clothes from bunching or wrapping around the drum
• Promotes consistent airflow by keeping items off the drum surface
• Fits into the drum interior at a mounting point and engages with normal drum rotation

• One drum mixing vane (gray)

• Replace only with the dryer unplugged and the gas supply turned off (if applicable)
• Access requires opening the dryer cabinet or removing the drum
• Inspect the mounting boss and fastener before installing; use OEM fasteners if required

This electronic control board manages a range of appliance functions so your unit runs the selected cycles and responds to user inputs. Replacing a faulty board restores normal control and cycle operation. What it does:

• Interprets user commands and controls cycle timing and sequencing
• Sends switching signals to motors, heaters, valves, and relays
• Manages display and panel feedback so settings and status appear correctly
• Failsafe symptom examples: no response to controls, cycles won't start or advance, erratic operation, or loss of display/indicator function

• Disconnect power at the breaker or unplug the appliance before starting work
• Handle the board by edges and avoid static discharge; wear an anti-static strap if available
• Verify the part number on the old board before installing to ensure compatibility

This retainer is a small fastener that secures a component inside your appliance, keeping it correctly positioned during operation. Replacing a damaged or missing retainer helps eliminate looseness and noise while preventing wear from parts shifting.

• Holds a mating part or assembly firmly in place
• Restores proper fit when the original retainer is cracked, warped, or missing
• Common symptoms: loose or misaligned parts, rattling/vibration, rubbing noises
• Helps prevent premature wear from movement or chafing

• Disconnect power; shut off gas and water supplies if applicable
• Use your model's diagram to locate the retainer and match its orientation
• Transfer any reusable hardware and ensure the retainer is fully seated
• Reassemble and run a short test to check for proper operation

This electrical wire harness connects key components to deliver power and signal paths so your appliance controls and features operate reliably. It replaces a damaged or worn harness to restore proper electrical connectivity. What it does:

• Routes power and signal between control board, sensors, and accessories
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps resolve symptoms like lights, fans, or controls not powering on or working erratically
• Maintains proper connector fit and wiring color-coding for correct hookups

• One electrical wire harness

• Disconnect power before inspecting or replacing the harness to avoid shock
• Confirm connector orientation and secure all clips; route wiring away from heat and moving parts
• Inspect mating connectors for damage and replace if corroded or burned

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This outer cabinet trim frame secures and finishes the appliance front, restoring a clean appearance and proper alignment of the control and door areas. It's a straightforward replacement for damaged or bent front trim. What it does:

• Replaces a worn, cracked, or dented outer cabinet frame to restore fit and finish
• Helps align adjoining panels and maintains a flush front appearance
• Keeps internal components protected by providing structural support at the front
• Addresses visible cosmetic damage and reduces gaps that can collect dirt

• One outer cabinet trim frame

• Disconnect power before beginning any repair to reduce risk of shock or injury
• Remove adjacent trim pieces and fasteners as needed; handle painted surfaces carefully to avoid scratches
• Use proper fasteners and torque to avoid warping the frame; some shifts may require minor realignment

This door gasket is the flexible sealing strip that helps keep cold air inside your refrigerator, improving temperature stability and efficiency. It replaces worn or torn seals to reduce drafts and moisture intrusion. What it does:

• Creates an airtight seal around the refrigerator door to help maintain proper internal temperature
• Helps prevent frost buildup and condensation by keeping warm, humid air out
• Reduces energy waste caused by cool-air leaks around the door
• Can fix common symptoms like warm spots near the door, excessive frost, or an overworking compressor

• High-level replacement: usually removed from the door channel and pressed into place; may require loosening door hinges for full removal on some models
• Check that the gasket sits evenly in the channel and that the door closes flush to ensure a proper seal
• Clean the door channel and mating surface before installing to ensure good adhesion and sealing

This main electronic control board manages a refrigerator's key functions, translating user commands and sensor signals into compressor, defrost and lighting operation for reliable daily performance. What it does:

• Receives inputs from the user interface and sensors, then controls compressor, fans and defrost cycles.
• Regulates cooling cycles to help maintain set temperatures.
• Powers and communicates with the display and status lights.
• Can cause symptoms such as a blank display, unresponsive controls, continuous run/overcooling, or intermittent cooling when failing.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Handle the board carefully and avoid electrostatic discharge; use proper grounding.
• Verify connectors and mounting location match your appliance before installation.

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive