Er36d-Sch/Ng Parts

Fixes F4 error codes, oven overheating, or inaccurate temperatures. This sensor monitors cavity temperature for reliable heating. Straightforward repair.

Restores bright indicator lighting for cooking zones on cooktops and ranges. Replace when zone indicator fails to illuminate. Verify fit with your model.

Oven won't heat or takes too long to preheat? This bake igniter assembly lights the gas burner to restore reliable baking and roasting performance.

Fix weak or failed ignition caused by gas leaks around the igniter assembly. This small rubber seal prevents air and gas leaks for reliable starts.

If your oven won't ignite or heat, the hot surface igniter likely needs replacement. This part ignites gas to heat your oven. DIY-friendly repair.

This transformer supplies the correct voltage to power the halogen light inside the appliance. It steps down household voltage to safely operate the halogen bulb. Replace this transformer if the halogen light no longer turns on even with a good bulb, or if the light flickers intermittently.

Seals the burner assembly to the cooktop surface, preventing gas leaks and stabilizing flames. Replace when worn, cracked, or causing ignition issues. Verify fit with your model number before ordering.

This outer surface burner ring replaces the damaged or worn ring on a gas cooktop, restoring proper gas flow and burner alignment for safer, more even heating. Fits specified Samsung surface burners. What it does:

• Replaces a cracked, warped or corroded outer burner ring to re-establish correct burner geometry
• Helps restore consistent flame pattern and even cooking across the burner
• Can resolve issues like uneven heating or gas flame wandering at the burner edge
• Works with the matching inner burner and cap to form the complete burner assembly

• One outer surface burner ring

• Turn off gas supply and disconnect power to the appliance before servicing
• Allow all components to cool completely; burner parts may have sharp edges—wear gloves
• Remove burner cap and inner components, seat the new outer ring fully before reassembly

Torx-head service screw secures panels, brackets, and access covers in wall ovens and ranges. Replaces missing or damaged screws to restore fit.

Factory wafer-head Phillips screw (#8 x 3/8 in) secures panels, brackets, and covers. Replace missing, stripped, or damaged screws for proper alignment.

Secures the LED assembly for stable indicator lights and display. Replace if lights are loose, misaligned, or flickering. Confirm fit with your model.

This service assembly secures the injector/nozzle in the washer dispenser area, ensuring proper positioning for reliable dispense performance. Replacing a worn or broken holder restores correct alignment and helps prevent leaks or missed dispensing cycles. What it does:

• Holds and aligns the detergent/bleach injector or nozzle within the dispenser assembly
• Keeps the injector sealed and positioned to reduce leaks or misdirected flow
• Helps restore proper dispense when the dispenser fails to deliver detergent or shows inconsistent dosing
• Works as a direct replacement for a cracked, broken, or missing injector support

• Disconnect power and shut off water before service
• Handle clips and plastic tabs carefully to avoid breakage during install

This straight bake burner replaces the oven's lower gas burner to restore consistent bake heat and flame. It installs in the oven floor and connects to the regulator and igniter assembly for normal gas flow to the bake chamber. What it does:

• Provides the primary gas flame for the oven's bake function
• Restores even baking when the oven fails to reach or hold set temperatures
• Replaces corroded, warped, or damaged burner tubes that produce weak or irregular flames
• Helps eliminate yellow or sputtering flames caused by burner damage or blockage

• One straight bake burner assembly

• Shut off power and gas supply before beginning service; follow all local codes
• Basic hand tools are typically required; gentle handling prevents deformation of the burner tube

Seals cooktop burner to stabilize the burner head and prevent debris buildup. Replace if damaged, cracked, or during burner maintenance. Confirm fit.

Rubber bumper cushions oven door and components. Replace if cracked, worn, or missing to restore quiet operation and prevent metal-on-metal contact.

A replacement service screw used to secure appliance panels and components. Durable fastener sized for common service points, making repairs and panel reassembly quick and reliable. What it does:

• Secures trim, access panels, brackets or small components during service and reassembly
• Commonly used where a shallow truss/wafer head is needed to sit flush without catching
• Helps stop rattling or loose parts caused by missing or stripped screws
• Matches OEM fit for compatible assemblies when the OEM part number is required

• One service screw (#8 x 1/2" truss/wafer head) as specified by the OEM part number

• Use the matching size driver to avoid cam-out and head damage
• Hand-start fasteners to avoid cross-threading; tighten until snug — do not overtighten
• Wear safety glasses and disconnect power before working on electrical appliances
• If a screw threads into plastic or thin sheet metal, consider replacing with the same OEM screw to preserve original threads