Fafs4474lwo Parts

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Replacement bolt fastener for securing washer panels, brackets, and assemblies. Needed when original bolt is missing, loose, or stripped causing rattling.

Support plate for washer components. Mounts internally to secure parts in place. Replace if cracked, bent, or broken to restore proper structural support.

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Secures hoses in your laundry center. Replace if cracked, loose, or causing leaks. Confirm fit with your model number before ordering.

Replacement mounting nut that secures panels, trim, and internal components. Needed when original nut is stripped, corroded, missing, or lost during repair.

Spring mounting bracket for washers. Secures suspension springs to the washer tub or frame. Replace if bracket is cracked, bent, or broken from load stress.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Washer hose clamp secures water inlet and drain hoses to prevent leaks. Replace if loose, cracked, or causing water drips. Verify fit with your model number.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Fix E53 errors, no spin, or drum not moving. This motor control board restores washer operation. DIY repair in 45 minutes with our installation video.

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

This main electronic control board regulates the appliance's functions and user interface so your appliance runs cycles and responds to commands. Replacing a failed board restores control and normal operation. What it does:

• Receives input from the control panel and sensors to manage cycles and timing
• Controls power to motors, valves, heaters, and other subsystems
• Updates display and responds to user commands when buttons or touch controls are used
• Can stop operation or cause error codes if the board is faulty or intermittently failing

• One replacement control board

• Disconnect all power before starting; electrical shock hazard if power remains connected
• Handle the board carefully and avoid static discharge; use ESD protection if available
• Verify this part number matches the service tag/parts list for your appliance before installing