Fdb1050reso Parts

Red

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

Color: White

This replacement spring provides the tension and return force needed for proper movement of a spring-loaded appliance component. Use it to restore smoother operation and consistent positioning where the original spring has worn or lost tension. What it does:

• Supplies tension and return force for hinges, latches or other spring-loaded mechanisms
• Helps restore proper movement and alignment of parts that sag, stick, or won't return to position
• Prevents excess play or slippage in spring-loaded assemblies when functioning correctly
• Works as a direct-fit replacement when the original spring is worn, stretched, or broken

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Use appropriate hand tools and eye protection; springs may be under tension and can release suddenly
• Compare the old spring to the new one for length, coil count and end type before installation

This replacement brace is a support bracket that helps secure and stabilize appliance panels and components, restoring proper alignment and reducing vibration. Designed for direct fit where the original bracket is damaged or missing. What it does:

• Provides structural support to panels, frames, or assemblies to maintain alignment and fit
• Secures components to prevent wobbling, rattling, or movement during operation
• Helps restore proper door or panel fit when a broken or bent bracket causes misalignment
• Reduces noise caused by loose or unsupported parts

• One replacement brace

• Disconnect power or unplug the appliance before starting any work
• Use the original screw locations and hardware where possible; save any reusable fasteners
• Inspect surrounding panels and mounting points for additional damage before reassembly

This is a genuine replacement screw used to secure appliance components and panels, restoring proper fit and function. It's a simple, reliable fastener for repair and maintenance tasks. What it does:

• Secures panels, brackets, trim, or internal components to restore stable assembly
• Replaces a stripped, missing, or rusted screw that prevents proper fastening
• Helps eliminate rattles or loose parts caused by worn fasteners
• Works where the OEM-specified screw is required for correct fit

• Use the correct screwdriver or bit to avoid stripping the head
• Hand-start the screw to ensure correct alignment before tightening
• Tighten only until snug—do not over-torque to avoid damage
• Disconnect power to the appliance before accessing internal components