Ffcd2413us Parts

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Secures the dishwasher door latch assembly to the cabinet. Replace if screw is stripped, missing, or damaged to restore secure latch installation.

Replacement screw for dishwashers. Secures panels, brackets, and trim to keep components properly aligned. Replace missing, stripped, or corroded screws.

Secures spray arm assembly components in your dishwasher. Replace if screw is stripped, loose, missing, or broken to keep the spray arm properly mounted.

Adjustable leveling leg threads into dishwasher base to support and stabilize the unit. Replace worn, missing, or broken feet to restore proper leveling.

Fix noisy humming, screeching sounds, or poor draining with a new sump assembly. Houses pump path and turbidity sensor for proper wash cycles.

Replace a cracked, broken, or missing dishwasher cover. This protective cap installs on your dishwasher to cover internal components and fittings.

Dishwasher won't start or stops mid-cycle? Burned or melted wires at the door latch often mean the main wiring harness has failed. Moderate DIY repair.

Replacement mounting screw for dishwasher panels and internal components. Secures brackets and chassis parts. Replace stripped, missing, or damaged hardware.

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit

Inner door panel installs inside the outer door panel to provide structure and rigidity. Replace if cracked, damaged, or worn to restore door integrity.

This small check ball sits inside the dishwasher's drain pump or water inlet valve and acts as a one-way valve to prevent water from flowing backward through the system. It ensures water moves in the correct direction during wash and drain cycles. Replace this part if you notice water draining back into the tub after a cycle completes, the dishwasher isn't draining properly, or water is leaking from the pump area.

Replacement mounting screw for dishwashers. Secures trim, panels, brackets, and internal components. Order when fasteners are missing, stripped, or corroded.

A small spring-style hose clamp that secures flexible tubing to fittings to help prevent leaks and hose separation. Replaces a worn or loose clamp to restore a tight seal on water and drain connections. What it does

• Compresses around a hose to hold it firmly on a barbed or smooth fitting
• Helps stop leaks and reduces chance of hose slip-off under pressure
• Commonly used on water, drain, and vent hoses where space is limited
• Simple, spring-action design keeps consistent tension as hoses expand/contract

• Disconnect power and shut off water supply before servicing appliance
• Use pliers to expand the clamp, slide into position, then release to seat it
• Inspect hose and fitting for damage; replace hose if cracked or brittle
• Do not overtighten or modify the clamp; replace with the exact style/size for a proper seal

Replacement mounting screw for dishwasher panels and components. Secures loose panels, brackets, and trim. Needed when original fasteners are missing, stripped, or worn.

If your appliance isn't responding to buttons or displays settings incorrectly, this control assembly restores cycle selection and electronic operation.