Fffh20f2qw Parts

This panel-mounted signal light is the small indicator lamp that illuminates when a function is active. It restores clear visual status on the control panel so you can tell at a glance when the appliance is operating. What it does:

• Lights to indicate when a feature, cycle, or function is on (model-dependent)
• Restores visible status feedback on the console or control panel
• Helps alert you if a function remains active after use
• Addresses issues such as no light, constant-on light, flickering, or a damaged lens

• 1 signal light

• Disconnect power at the breaker before servicing
• Access the control panel/console; remove knobs and screws as needed
• Note wire positions or take a photo; transfer wires to the new light
• Secure the light in the panel, reassemble, restore power, and test

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

Color: White

This hinge cover protects and finishes the appliance's door hinge, restoring a clean appearance and helping keep the hinge area clear of dirt and debris. A simple cosmetic and protective replacement. What it does

• Covers and shields the door hinge to protect it from dust, grease and debris.
• Restores the appliance's finished appearance when the original cover is cracked, broken, or missing.
• Helps reduce the chance of exposed sharp edges from a damaged hinge area.
• A damaged or missing cover can contribute to visible hinge hardware and may make the door look misaligned.

• Support the door before removing any hinge hardware to prevent the door from shifting or falling.
• Handle edges carefully and wear gloves to avoid cuts from metal parts.
• Reinstall original mounting screws or clips; do not overtighten plastic components.

This door stop controls the door's swing, preventing it from opening past its designed angle and protecting the hinge and cabinet. Replace a cracked or missing stop to restore controlled door movement and help maintain proper alignment and sealing.

• Limits door opening angle to prevent overextension
• Helps protect hinges and prevent cabinet/wall impact
• Supports consistent door alignment and gasket contact
• Typical signs: door swings too far, visible broken/missing stop, scuffing near hinge area

• Disconnect power and support or unload the door to reduce weight before servicing
• Support the door; remove hinge cover/hardware as required by your model
• Note the original stop's orientation; transfer and secure with existing hardware
• Adjust hinges if needed

This replacement drain pan collects defrost water from the evaporator and holds it in the machine compartment so it can evaporate. Replacing a cracked, warped, or missing pan helps prevent puddles under the appliance and musty odors. What it does:

• Collects defrost and condensate water routed through the drain tube
• Sits near the compressor/condenser so heat and airflow aid evaporation
• Helps prevent floor leaks caused by a damaged or misaligned pan
• Common symptoms may include water under the unit, visible pan cracks/warping, rattling from a loose pan, or persistent musty smells

• Includes 1 drain pan

• Unplug the appliance and pull it forward to access the rear; remove the lower rear access panel
• Remove the old pan and transfer any clips or supports if present
• Seat the drain tube into the new pan and position the pan level, clear of moving parts
• Reinstall the access panel and restore power; check for proper drainage after a defrost cycle

This replacement screw secures panels, brackets, or internal components in select Frigidaire-made refrigerators and freezers. Use it to replace missing or stripped hardware and restore a secure fit to help reduce vibration and noise.

• Fastens appliance panels, brackets, and internal components
• Helps prevent vibration, rattling, or looseness from missing hardware
• Reliable fix when the original screw is missing, damaged, or stripped
• Designed for proper fit in the original threaded location(s) specified for this part number

• Disconnect power to the appliance before servicing
• Align parts and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten, especially into plastic components
• Reuse any original washers or clips if present and in good condition

This support is a small mounting bracket used inside the appliance to hold an interior component, such as a shelf or basket. Replacing a cracked or missing support restores a secure, level fit and helps prevent wobbling or dropping.

• Provides a stable mounting point for a shelf, basket, rail, or panel
• Keeps interior components aligned and level
• Common symptoms: shelf/basket tilts, won't seat, or falls; visible cracks or missing support
• Replace if broken, deformed, or worn to restore proper fit

• Disconnect power and clear the work area before starting
• Remove the affected shelf/basket/panel to access the mounting point
• Release the damaged support (snap tabs or remove screw), align, and install the new support
• Reinstall the component and verify it sits level and secure

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models. 

This screw set replaces missing, stripped, or damaged fasteners to secure components in your appliance. Restoring proper hardware helps keep parts aligned, reduces rattling, and maintains a solid, reliable fit. What it does:

• Fastens panels, brackets, and other components as specified by the manufacturer
• Replaces worn or lost screws to restore secure attachment points
• Helps resolve loose handles or panels, vibration/rattling noises, and shifting parts
• Supports correct alignment for dependable operation

• Screw set as supplied by the manufacturer

• Disconnect power before servicing; wear cut-resistant gloves
• Support the part being fastened (door, panel, bracket) to prevent damage
• Start screws by hand to avoid cross-threading; tighten evenly and do not overtighten
• Replace one screw at a time to maintain alignment

This light socket securely holds the appliance bulb and provides the electrical connection to illuminate the compartment when the door is opened. Replacing a faulty socket restores interior lighting so you can easily see contents.

• Provides the electrical connection and physical mounting for the light bulb
• Common failure symptoms: light won't turn on, flickers, or only works when the bulb is jiggled
• Show signs of heat discoloration, loose terminals, or intermittent contact

• Unplug the appliance before service; power is off
• Allow the bulb and surrounding area to cool before handling
• Handle wiring carefully; transfer conductors to the new socket one at a time to maintain correct connections
• Do not exceed the bulb type/wattage specified on the appliance rating label

Screen - drain keeps the drain path clear by trapping lint and small debris before it reaches the pump or drain hose, helping reduce clogs and improve drainage. Simple replacement restores proper water flow and drain performance. What it does:

• Traps lint, hair and small debris to help prevent clogs in the drain path
• Helps maintain consistent water drainage and pump operation
• Replace if you notice slow draining, standing water, or visible debris at the drain opening
• Sits in the appliance's drain assembly to protect downstream components

• Disconnect power to the appliance before servicing; turn off the water supply if the model requires it
• Access the drain area per your model's service instructions (remove access panel or wash tub components as needed)
• Inspect surrounding seals and hoses for damage and clean mating surfaces before installing the new screen