Ffgf3054tw Parts

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

The Burner Grate is an OEM part for Frigidaire gas ranges. It supports racks and pans directly over the range's gas burners during cooking. The burner grate must withstand constant exposure to high heats without warping or degradation.

Causes of a bad burner grate include wear from heavy use over multiple years, corrosion from spills or food particles left on the grate, or cracks and chips that compromise durability and function.  

Symptoms of a bad burner grate are:

• Uneven or inefficient heat transfer to pots and pans during cooking  
• Warping or distortion of grate bars impacting pan support
• Sharp edges or breakage causing potential safety hazards

This OEM replacement grate is also compatible with some Electrolux, Crosley, and Amana gas ranges. 

This manifold supply tube routes gas from the appliance's inlet/regulator to the burner manifold and valves. Replacing a damaged tube helps restore safe, consistent fuel delivery and reliable burner performance. What it does

• Channels gas from the regulator/inlet to the burner manifold/valve assembly
• Maintains proper fuel flow to multiple burners
• Replace if the tube is bent, cracked, corroded, or leaking
• Symptoms can include multiple burners not lighting or weak/uneven flames due to restricted flow

• 1 manifold supply tube

• Shut off the gas supply and disconnect electrical power before servicing
• Note the routing and orientation of the original tube to match bends and connections
• Use only approved practices for your fitting type; do not apply sealant to flare-seat connections
• After installation, perform a soap-and-water leak test on all joints; do not operate if bubbles appear

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

Color: White

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:

• Provides a secure plug-in connection between a wire harness and a component
• Restores power to a component when the original connector is cracked, melted, or corroded
• Helps prevent loose connections that can cause intermittent operation or sparks
• Fits the OEM-style wiring configuration for a direct replacement

• Disconnect power to the appliance before starting any repair
• Remove the damaged connector and match the replacement to the harness before installing
• Use basic hand tools; avoid forcing terminals to prevent damage