Fgbd1438pf3a Parts

This is a replacement dishwasher rack assembly with factory-installed wheels. It restores smooth sliding and safe loading when the original rack is bent, rusted, or missing rollers—helping the rack glide properly and keep items positioned during the wash.

• Holds and organizes dishes, glasses, and cookware during cycles
• Integrated wheels ride on the tracks for easy loading and unloading
• Replace if tines are rusted/broken, wheels are cracked or missing, or the rack derails
• Helps prevent items from tipping and maintains consistent spray coverage

• Disconnect power to the dishwasher before servicing
• Open the door, extend the rack, release any rail end-stops, and remove the old rack
• Transfer any removable accessories from the old rack to the new one, if needed
• Slide the new rack onto the rails and reinstall end-stops; verify smooth operation

This bezel is a trim piece for Frigidaire dishwashers that finishes and protects an opening on the door/control panel, helping the mating component sit properly while restoring a clean, factory look.

• Frames and protects the panel opening for a control or latch component
• Helps keep the mating part aligned and seated correctly
• Covers raw edges and gaps to reduce wear and debris buildup
• Common symptoms: broken or missing trim, loose/wobbly bezel, cracked retaining tabs, cosmetic damage

• Disconnect power to the dishwasher before servicing
• Remove the control knob or latch handle to access the bezel
• Release the bezel's retaining tabs/clips and lift it out from the panel
• Align the new bezel and snap/secure it into place; reinstall any removed parts and test operation

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This replacement screw secures appliance components so panels, brackets, and trim stay tight and properly aligned. Replace a missing, stripped, or corroded fastener to restore a solid fit and help stop vibration or rattling.

• Fastens components to the chassis or assembly for correct fit
• Helps maintain alignment and reduce movement and noise during operation
• Restores secure mounting when original hardware is missing, rusted, or stripped
• Typical symptoms: loose panel or handle, rattling noises, hardware backing out

• Disconnect power; if servicing a dishwasher, also shut off water
• Match the screw to the original location before installation
• Start threads by hand to avoid cross-threading, then tighten snugly without overtightening

Filter only. Fine filter not included.

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This is a genuine replacement mounting screw used to secure appliance panels and components. It restores proper fit and helps prevent rattling or loose parts for safe, reliable operation. What it does:

• Fastens panels, trim pieces, or internal components to maintain proper alignment
• Secures parts that can vibrate or become loose during normal use
• Helps stop rattling, squeaks, or gaps caused by missing or damaged fasteners
• Suitable wherever the OEM specifies part 154041001 as the required screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screw hole and match thread engagement; do not force or cross-thread
• Tighten firmly but avoid over-torquing to prevent stripped threads or cracked panels
• If multiple or different screws were removed, keep track of each location for correct reassembly

A replacement switch mounting screw that secures control switches and switch assemblies in place for reliable operation. Replaces lost or stripped mounting hardware to restore secure panel and switch attachment on compatible appliances. What it does:

• Fastens the switch or switch bracket to the appliance frame or control panel
• Keeps electrical switch connections stable to prevent intermittent contact or movement
• Helps eliminate loose or rattling switches and noisy control panels
• Restores proper alignment of the switch for reliable user control

• Turn off power to the appliance before accessing the control panel to avoid shock
• Use the matching screwdriver size to avoid stripping the screw head
• Tighten securely but do not over-torque to prevent damage to the switch or panel
• Replace all affected fasteners for a secure fit