Fghb2866peo Parts

This refrigerator drain tube channels defrost water from the evaporator to the rear drain pan so it can evaporate. Replace a cracked, missing, or clogged tube to stop interior leaks and ice buildup.

• Routes defrost meltwater from the freezer drain to the condenser drip pan
• Helps prevent pooling under crisper drawers or water on the floor
• Common failure symptoms: water under drawers, ice sheet in the freezer bottom, recurring drain clogs or freeze-ups, dripping at the rear base
• Restores proper drainage when the original tube is brittle, split, or obstructed

• Disconnect power; pull the unit forward and remove the lower rear access panel
• Remove the old tube from the drain outlet and drip pan; clear any ice/debris with warm water—avoid sharp tools
• Seat the new tube fully on the drain outlet and position the outlet into the pan; verify flow by pouring warm water down the drain
• Restore power and monitor for leaks as normal defrost cycles resume

This door-activated light switch installs in the refrigerator liner and opens or closes the circuit to the interior lamp as the door moves. It restores reliable, automatic on/off lighting when you open and close the door. What it does:

• Controls the interior light based on door position
• Helps fix a light that won't turn on with the door open
• Helps fix a light that stays on when the door is closed
• On some models, also signals door-ajar/dispenser interlock functions

• 1 light/lamp switch

• Disconnect power to the refrigerator before servicing
• The switch is typically in the door jamb; gently release and pull it out, then transfer wires one at a time to the new switch
• Match wire positions/orientation and seat the switch flush to prevent air leaks
• Test door operation and light before finalizing reassembly

This factory screw secures components inside your refrigerator. Replacing a missing, rusted, or stripped fastener restores a tight, rattle-free fit for shelves, panels, and brackets so everything stays aligned, supported, and quiet.

• Fastens panels, brackets, or trim to the cabinet/liner
• Replaces damaged, corroded, or stripped hardware
• Helps resolve looseness, vibration, rattling, or misalignment
• Maintains proper support for shelves, covers, and assemblies

• Unplug the appliance; if working near water lines, shut off the water supply
• Match the new screw to the original; transfer any washers or spacers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving clip/insert is damaged, replace it to ensure a secure repair

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

This slide assembly mounts inside the refrigerator to support and guide a slide-out shelf or drawer. Replacing a worn or broken slide restores smooth travel, alignment, and easy access to stored items. What it does:

• Provides the track/rail that lets a shelf or drawer slide in and out smoothly
• Helps keep the shelf/pan level and properly aligned
• Can resolve sticking, rough or noisy travel, sagging on one side, or a cracked/broken rail
• Restores full extension and proper seating of the shelf or drawer

• 1 slide assembly

• Unplug the refrigerator and remove contents from the affected shelf/drawer
• Remove the shelf or drawer and retain mounting screws or clips
• Note slide orientation; transfer any reusable stops or clips from the old slide
• Secure the new slide with existing hardware and test for smooth operation

This slide assembly restores smooth, stable movement to your refrigerator drawer or basket so it opens and closes easily and stays aligned. Replace a worn or cracked slide to eliminate sticking, sagging, or track problems.

• Guides and supports the drawer/basket along the cabinet track
• Maintains alignment to prevent binding, rubbing, or popping off the rail
• Restores full, smooth travel for easier access to contents
• Common symptoms: drawer hard to open/close, sits crooked, falls off track, or makes scraping/clicking noises

• Disconnect power and remove the drawer and contents before starting.
• Note the slide's orientation; remove mounting screws/clips and the old slide.
• Install the new slide in the same position; transfer any snap-on brackets from the original if applicable.
• Reinstall the drawer, ensuring both sides are seated on the tracks, and test for smooth operation.

This water fill chute kit channels incoming water from the fill tube into the ice maker mold. Replacing a cracked or deformed chute helps stop leaks and ice buildup at the fill area and supports consistent, properly directed fills for reliable ice production.

• Directs water from the inlet/fill tube into the ice maker mold during the fill cycle
• Helps prevent splashing, leaks, and ice accumulation at the fill point
• Replaces damaged, warped, or missing chute/funnel components
• Typical symptoms: water dripping near the ice maker, frost/ice around the fill area, cubes clumping together, intermittent ice production

• Disconnect power and shut off the household water supply before servicing
• Remove the ice bin and access the fill area at the rear/top of the ice maker
• Clear any ice blockage; remove fasteners/clips to take out the old chute; transfer any seals or grommets if present
• Align the new chute with the fill tube and mold, seat fully, secure, then restore water/power and run a test fill to check for leaks

This mullion guide secures and aligns the refrigerator's vertical door trim so doors close evenly and seals engage properly. Replacing a worn or broken guide helps restore door alignment and reduce drafts at the center seam. What it does:

• Holds the mullion/vertical trim in place and keeps the trim flush with the cabinet
• Guides the doors during closing to maintain even gaps and seal contact
• Prevents the mullion from shifting, rattling, or catching when doors open or close
• Common symptom: loose, misaligned, or damaged center trim causing wind, noise, or uneven door gaps

• Disconnect power before starting service and work on a stable surface
• Remove the mullion/trim and any surrounding gaskets or screws as needed to access the guide
• Use appropriate trim/removal tools to avoid damaging adjacent plastic or gasket material
• Reinstall hardware securely and verify doors close and seals engage properly after installation

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This piece replaces the flip-up cover for the cheese/butter compartment on your refrigerator door. It restores a tidy, enclosed spot for butter and small dairy items, helping keep contents contained and easy to access.

• Covers the dairy bin on the fresh food door; flips up for quick access
• Helps contain and protect butter/cheese items to reduce spills and mess
• Replace when cracked, warped, missing, or no longer stays attached/closed
• Designed to fit the designated hinge points for the dairy compartment on applicable models

• Disconnect power before servicing
• Allow plastic parts to warm to room temperature to reduce risk of cracking
• Align door tabs with the hinge posts on the compartment and press until fully seated
• Open and close the door to ensure smooth operation

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

This bushing is a small bearing insert that supports a pin or shaft within an appliance mechanism. Replacing a worn bushing restores smooth movement and helps prevent accelerated wear, scraping, and noise in the affected assembly.

• Provides a low-friction surface for pivoting or sliding components
• Helps correct loose, wobbly, or uneven movement
• Can reduce squeaking, scraping, or binding during operation
• Replaces cracked, distorted, or missing bushings to maintain alignment

• Disconnect power and, if applicable, shut off the water supply before servicing
• Note the original bushing's orientation and depth; seat the replacement fully in the same position
• Inspect the mating pin/shaft and surrounding bracket/hinge for wear; replace any damaged parts
• Do not overtighten fasteners through plastic and avoid lubricants unless specified by the manufacturer

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water filter cover encloses the refrigerator's filter housing for a clean look and protection. Replace a cracked, loose, or missing cover to restore a secure, smooth-opening access door for routine filter changes.

• Covers and protects the water filter in the fresh food compartment
• Opens to provide access when replacing the filter
• Helps prevent items from catching on the filter or housing
• Replace if the cover is cracked, the hinge or latch is broken, it won't stay closed, or it's missing

• Disconnect power and shut off the water supply before servicing
• Open the filter area and release the retaining tabs or hinge pins to remove the old cover
• Transfer any screws or hinge pieces from the original part if required
• Align and snap or secure the new cover; verify smooth opening and closing

Color: Stainless Steel
The Dispenser Trim is an OEM part for Frigidaire refrigerators. It surrounds the ice and water dispenser area located externally on the refrigerator door.

Causes of a faulty dispenser trim can include cracks, chips or damage from impacts or general wear over time.

Symptoms of failure include:

• Water leaks developing around the dispenser opening
• Loose or detached trim that does not sit flush
• Access to dispenser functions being obstructed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.