Fghb2866peo Parts

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

This bushing is a small bearing insert that supports a pin or shaft within an appliance mechanism. Replacing a worn bushing restores smooth movement and helps prevent accelerated wear, scraping, and noise in the affected assembly.

• Provides a low-friction surface for pivoting or sliding components
• Helps correct loose, wobbly, or uneven movement
• Can reduce squeaking, scraping, or binding during operation
• Replaces cracked, distorted, or missing bushings to maintain alignment

• Disconnect power and, if applicable, shut off the water supply before servicing
• Note the original bushing's orientation and depth; seat the replacement fully in the same position
• Inspect the mating pin/shaft and surrounding bracket/hinge for wear; replace any damaged parts
• Do not overtighten fasteners through plastic and avoid lubricants unless specified by the manufacturer

This water filter cover encloses the refrigerator's filter housing for a clean look and protection. Replace a cracked, loose, or missing cover to restore a secure, smooth-opening access door for routine filter changes.

• Covers and protects the water filter in the fresh food compartment
• Opens to provide access when replacing the filter
• Helps prevent items from catching on the filter or housing
• Replace if the cover is cracked, the hinge or latch is broken, it won't stay closed, or it's missing

• Disconnect power and shut off the water supply before servicing
• Open the filter area and release the retaining tabs or hinge pins to remove the old cover
• Transfer any screws or hinge pieces from the original part if required
• Align and snap or secure the new cover; verify smooth opening and closing

Color: Stainless Steel
The Dispenser Trim is an OEM part for Frigidaire refrigerators. It surrounds the ice and water dispenser area located externally on the refrigerator door.

Causes of a faulty dispenser trim can include cracks, chips or damage from impacts or general wear over time.

Symptoms of failure include:

• Water leaks developing around the dispenser opening
• Loose or detached trim that does not sit flush
• Access to dispenser functions being obstructed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Slide Assembly is an essential OEM component for Frigidaire refrigerator drawers. It provides smooth extension and retraction of covered storage bins during access.  

Symptoms of a faulty slide assembly include:

• Squeaking or rubbing noises coming from drawer rails   
• Difficulty smoothly pulling out covered bins
• Scratches or gouges visible along wear surfaces

Causes involve years of constant sliding stresses overwhelming lubrication, leading to increased friction. Without smooth gliding, premature deterioration of plastic drawer supports results.

This authentic OEM replacement is compatible with Frigidaire, Electrolux, and Kenmore models.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement bar is a direct-fit support component that helps hold and stabilize a refrigerator door or interior shelf assembly, restoring secure storage and preventing items from shifting or falling. What it does

• Provides structural support for a door or shelf ledge to keep stored items secure
• Replaces bent, cracked or broken bars that allow shelves or door bins to sag
• Helps stop rattling or movement from loose or damaged supports
• Restores proper alignment so shelves and bins sit flush and stable

• One replacement bar

• Disconnect power before removing refrigerator doors or interior components when necessary
• Remove affected shelf or bin to access mounting points
• Use basic hand tools; avoid overtightening fasteners to prevent cracking plastic parts
• Handle glass shelves and door bins carefully during removal and reassembly

This electronic power control board manages incoming power and directs it to the refrigerator's compressor, fans, and control circuits. Replacing a failed board can help restore cooling performance and bring unresponsive or intermittently running units back to normal operation.

• Distributes and regulates power for the compressor and fan motors; failure can leave the unit warm or silent
• Sequences cooling operations based on sensor/control inputs; faults may cause intermittent starting or frequent power cycling
• Interfaces with the refrigerator's controls to execute cooling commands; issues can present as an unresponsive control panel
• Contains relays and protective circuitry; burn marks or repeated relay clicking can indicate a defective board

• Disconnect power before service; use anti-static (ESD) precautions when handling the board
• Board is typically located at the back of the refrigerator in the machine compartment behind the rear access panel
• Photograph wiring; move connectors and any jumpers to the new board, matching positions and orientation
• Ensure all plugs are fully seated, reassemble, restore power, and allow up to 24 hours for temperatures to stabilize

This right-hand wire basket slide supports and guides the basket as it opens and closes. Replace it if the basket binds, tilts, or no longer glides smoothly due to a worn, cracked, or broken slide.

• Provides the track for the basket to slide in and out on the right side
• Helps keep the basket aligned and stable within the compartment
• Common symptoms: sticking or uneven travel, basket tilts/drops on one side, visible cracks or damage
• Restores smooth operation and proper support for the wire basket

• Disconnect power and remove the basket and contents before starting
• Remove screws or clips securing the old slide; retain fasteners for reuse
• Align and secure the new slide in the same mounting locations
• Reinstall the basket and verify smooth operation before loading

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

This refrigerator housing is the molded support used to mount and protect its associated components inside the appliance. Replacing a damaged housing restores a secure fit and proper alignment so parts stay in place and function correctly.

• Provides structural support and mounting points for the related controls/components
• Helps route air and/or wiring as designed by the manufacturer
• Restores proper alignment to reduce rattles, rubbing, or interference
• Symptoms can include cracked plastic, broken tabs, loose or sagging assemblies, or components that won't stay secured

• Disconnect power before servicing; shut off water as needed if working near dispenser/ice components
• Transfer sensors, wiring, controls, and hardware from the original housing unless new parts are supplied
• Reuse original screws/clips; avoid overtightening to prevent cracking
• Verify harness connections and clearances before restoring power and water

This replacement retainer clip secures trim, panels or small components inside your appliance to restore proper fit and reduce rattling. A simple, low-cost part commonly used where plastic or metal pieces need a secure hold. What it does:

• Holds panels, trim pieces or small assemblies in place to prevent shifting and vibration.
• Helps stop rattling, loose trim or components that don't stay seated.
• Keeps wiring or hoses routed and restrained when used as a harness/route clip.
• Suitable when original clip is cracked, broken or missing.

• Disconnect power to the appliance before beginning any work.
• Remove surrounding trim or panels gently to access the clip location; a trim tool or small screwdriver may be helpful.
• Clip installs by pressing into the mating slot or hole until it snaps; pliers may assist for removal/replacement.
• Verify correct orientation and fit by comparing the new clip to the old one before final reassembly.

The Slide Assembly is an OEM part for Frigidaire refrigerators. It secures crisper and pantry bins within the refrigerator interior, providing gliding functionality for easy access to stored items.

Causes of a bad slide assembly can include loose or broken mounting features, damaged rollers, or bent metal rails failing to guide bins smoothly. 

Symptoms of a bad slide assembly include:

• Difficulty removing or replacing crisper/pantry bins  
• Bins failing to close fully or stay securely in place
• Loud squeaking or grinding noises developing
• Dislodged mounting screws or loose mounting points

Replacing with this OEM slide assembly restores smooth operation. It is purpose-built to support everyday use without degradation.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before further component wear develops.

This refrigerator bracket is the OEM mounting piece that secures a specific internal assembly in place. Replacing a cracked or missing bracket restores a solid fit, proper alignment, and smooth, rattle-free operation of the attached component.

• Provides a rigid mounting point for the designated refrigerator component
• Maintains proper alignment to help the assembly operate correctly
• Helps reduce vibration and movement that can cause noise or wear
• Typical signs of failure: broken tabs, stripped holes, loose or misaligned parts

• Disconnect power; turn off water supply if working near ice/water components
• Access the area per your product's diagram; retain and reuse existing screws/fasteners
• Transfer any clips, spacers, or grommets from the old bracket to the new one
• The mounted component seats fully and operates before reassembling panels/shelves