Fghf266pf3 Parts

This electronic main control board manages and distributes power to the appliance's key components. Replace a failed board to restore normal operation when the unit won't power up, won't start, or runs erratically.

• Regulates and routes incoming power to motors, fans, compressors, heaters, and valves based on signals from sensors and the user interface
• Coordinates cycle timing and system protections to help prevent component damage
• Logs or triggers fault indications when abnormal conditions are detected
• Common failure symptoms: no power, dead/unresponsive controls, intermittent shutdowns, or unpredictable operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, compressor, valves) for shorts before restoring power

Replacement screw secures door handles, brackets, panels, and trim to refrigerator mounting points. Install when hardware is missing, stripped, or loose.

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

Channels defrost water from the evaporator to the rear drain pan. Replace this tube if it's cracked, clogged, missing, or has become brittle over time.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Refrigerator handle mounting block that secures door handles to the refrigerator door. Replace if cracked, broken, or missing to restore proper handle attachment.

Fix cracked or damaged dispenser trim on your refrigerator. This external trim piece surrounds the ice and water dispenser area on the door.

Small retainer clip that secures components, panels, tubes, or wires in place inside your refrigerator. Replace when worn, broken, or missing to restore fit.

This slide set replaces the right- and left-hand rails that guide and support a drawer or rack. It restores smooth, aligned movement so the assembly opens and closes easily without sticking, wobbling, or jumping off the track.

• Guides and stabilizes the drawer/rack on both sides for smooth travel
• Maintains alignment to reduce binding, uneven movement, and premature wear
• Replaces worn, bent, or broken slides that affect operation
• Common symptoms: sticking, rough/grinding movement, tilt or sag, popping off track, hard to open/close

• Disconnect power; shut off gas/water. Remove the drawer or rack before servicing.
• Note L/R orientation; remove old slides and reuse existing screws/brackets.
• Install new slides in the same positions; ensure they are fully seated and aligned.
• Test movement several times before returning the appliance to service; wear cut-resistant gloves.

Left-hand gray upper hinge cover snaps over the top door hinge to conceal hardware and restore a finished look. Replace when cracked, broken, or missing.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Support bar for refrigerator freezer drawer assembly. Installs between roller tracks to stabilize drawer and prevent shifting. Replace if broken or missing.

Flip-up cover for the cheese and butter compartment on your refrigerator door. Replace if cracked, broken, or missing to keep dairy items contained.