Fgid24466qf Parts

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This dishwasher hose routes water between internal components to support proper wash and drain performance. Replacing a cracked or leaking hose helps prevent water damage and restores reliable water flow inside the machine. What it does:

• Carries water between internal components during wash and drain cycles
• Helps maintain a watertight path to prevent leaks inside the cabinet
• A damaged hose can lead to puddles under the unit, water in the base pan, or reduced wash/drain performance
• Visible splits, pinholes, soft spots, or kinks are signs the hose needs replacement

• 1 hose

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher forward for access and place towels to catch residual water
• Transfer/reuse existing clamps or replace if worn; ensure secure, leak-free connections
• Route the hose without kinks and run a short test cycle to check for leaks

This drain pump assembly removes water from the tub at the end of wash and rinse cycles, helping your appliance complete cycles and prevent standing water.

• Pumps wastewater out through the drain hose to the household drain
• A failing pump can cause slow or no draining, cycle interruptions, or error codes related to draining
• May also present as water left in the tub or an inability to start the spin/drain portion of a cycle

• Unplug appliance and shut off water supply before service
• Have towels or a pan ready—residual water will drain when hoses are removed
• Note wire and hose orientations before disconnecting; transfer any mounting hardware from the original if reused
• After installation, check for leaks and run a short drain cycle to verify operation

This Rack Roller is an OEM part for Frigidaire dishwashers. It is an essential component for the smooth and stable movement of the dishwasher rack. 

Rack rollers can wear down or become damaged due to regular use, excessive load, or general wear and tear. A malfunctioning rack roller can make it difficult to slide the rack in and out, and may even cause the rack to become misaligned or unstable.

Symptoms of a failing rack roller in a dishwasher include:

• Difficulty in sliding the dishwasher rack in and out.
• A wobbly or unstable rack during movement.
• Unusual noises, such as scraping or squeaking, when the rack is moved.
• Visible wear or damage on the rollers.
• The rack getting stuck or not sitting properly in the dishwasher.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This cover is a protective panel used on Frigidaire appliances to shield and finish a specific assembly. Replacing a cracked or missing cover helps protect internal components and maintain proper routing or airflow so the unit operates as intended. What it does

• Shields internal parts from dust, moisture, and accidental contact
• Helps guide airflow or water within the assembly
• Secures adjacent components and restores a clean, finished appearance
• Typical symptoms: cracks, broken tabs, looseness/rattling, warping, or a missing panel

• 1 cover

• Disconnect power; if the appliance uses water, also shut off the supply
• Note fastener locations and transfer any clips or inserts from the original cover
• Inspect mating surfaces and any seals; replace damaged seals if needed
• Do not overtighten screws; verify clearances and wire routing before restoring power

This small retainer clip secures a mating part in the correct position inside your appliance, helping prevent movement, premature wear, and noise. Replace a cracked, bent, or missing clip to restore a tight, reliable hold.

• Provides a positive hold to keep the component properly seated
• Maintains alignment to reduce vibration and rattling during operation
• Helps prevent parts from backing out or disconnecting over time
• Common signs of failure: loose or misaligned component, rattling, clip that falls off, or visible damage

• Disconnect power; if working near any water connections, also shut off the water supply
• Note the clip's original orientation and position before removal
• Use needle-nose pliers or a small flat-blade screwdriver to release/install; avoid deforming mating tabs
• Ensure full engagement and that the secured part is firmly held before reassembly and testing

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

The Dishwasher Manifold is an OEM part for Frigidaire dishwashers. It is a complex component that controls the flow of water through the various spray arms and nozzles within the dishwasher.

Causes can be mineral buildup or sediment that disrupts water flow, cracks or leaks in internal waterways, or damage from impact or unbalanced loads.

Symptoms of a bad Manifold include:

• Inadequate water pressure to one or more spray zones
• Blocked or clogged spray nozzles or arms
• Insufficient water flow for proper cleaning

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Drain Filter is an OEM component specifically designed for Frigidaire dishwashers. It is designed to trap food particles and debris from exiting the dishwasher and entering plumbing drains.

Causes of failure usually stem from normal wear and potential mineral deposits reducing pore size over many years of use. Hard water areas present additional stress. 

Symptoms of a clogged or ineffective drain filter include:  

• Slow or incomplete draining after cycles
• Gurgling noises from drain line blockages
• Potential plumbing backups and repairs from unfiltered waste

This OEM part fits Electrolux, Gibson and Kenmore models as well.

The Control Panel is an OEM part for Frigidaire dishwashers. Located at the front of the dishwasher door, the control panel features buttons and displays that allow for the selection and monitoring of wash cycles. Printed electronic circuits distribute input signals to initiate the appropriate cycle settings.

Causes of a bad Control Panel can include cracked or damaged screens, non-responsive buttons, or failures of internal electronic pathways over time. 

Symptoms of a bad Control Panel include:

• Faulty or unreadable display screens  
• Random cycle activation without input
• Repeated error codes or flashing lights
• Physical damage or loose components  

This genuine OEM Frigidaire part is compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models as well.

The Control Board is an OEM replacement part for Frigidaire dishwashers. Located inside the cabinet behind the control panel, the control board utilizes integrated circuits and electronic components to regulate all dishwasher functions. It receives input signals from the control buttons to initiate and monitor the wash cycle. 

Causes of a bad control board can include failures of electronic components over time, voltage fluctuations that cause circuit damage, or moisture infiltration leading to corrosion.

Symptoms of a bad Control Board include:

• Dishwasher fails to start or stops mid-cycle unexpectedly
• Lights or displays on control panel malfunction  
• Inability to select options or cycles
• Complete non-responsiveness of control functions

This board is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

The Door Lock is an OEM part for Frigidaire dishwashers. As a basic safety component, it secures the dishwasher door firmly closed during active wash cycles. Trapping steam and heat within the tub area is crucial for sanitizing soils and delivering clean dishes.

Symptoms of a faulty door lock include:

• Inability to fully latch or lock the dishwasher door closed  
• Accidental opening of the door during washing interruptions
• Possible leaks or loss of heat from unsealed door cracks
• Partial or incomplete cleaning cycles 

Causes of a failed lock can be wear over extended use, or damage to the locking latch or striker plate. Warped or misaligned doors also put undue stress on the lock mechanism.

Replacing with this genuine Frigidaire part restores secure closure and safe operation. It is also compatible with some Kenmore, Gibson, and Admiral branded dishwasher models. Proper door locking is essential for optimal washing performance.
 

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser so your appliance makes ice and dispenses water reliably. Replaces a failed valve to restore normal water delivery and prevent leaks. What it does:

• Opens and closes to route household water to the ice maker and dispenser when signaled.
• Stops water flow when the fill cycle ends to prevent overfilling.
• Commonly replaces valves causing no water to the dispenser or ice maker.
• Also used when valve leaks or runs continuously.

• Turn off the refrigerator and shut off the water supply before starting work.
• Disconnect electrical connectors and water lines carefully; expect minor residual water.
• Inspect hose fittings and seals; test for leaks after installation.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.