Fgid246qf2a Parts

This pulley guides the dishwasher door's balance cable so the springs can counterweight the door. Replacing a worn or broken pulley restores smooth, controlled door movement and helps prevent the door from dropping or feeling heavy.

• Guides the door balance cable/cord to maintain proper spring tension
• Helps the door open and close smoothly and evenly
• Visible cracks, wobble, or flat spots on the wheel indicate replacement

• Disconnect power and shut off water before servicing
• Remove the toe-kick to access the side spring/cable area
• Support the door and carefully relieve spring tension; note the cable routing through the pulley
• Install the new pulley in the original position and inspect related cable/link and spring for wear

This replacement bracket secures and supports an internal component in your appliance, restoring a stable mount and proper alignment. Install when the original bracket is cracked, bent, missing, or no longer holds the part firmly.

• Provides a rigid mounting point for the associated component
• Helps prevent shifting, sagging, vibration, or rattling from a loose mount
• Restores proper alignment for reliable operation
• Replaces a broken, warped, or missing bracket

• Disconnect power and, if applicable, shut off water/gas before servicing
• Note bracket orientation; transfer any spacers or hardware from the original
• Align bracket squarely and secure with appropriate fasteners; avoid overtightening
• Verify alignment and operation before reassembly

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This is the front console/control panel assembly for the appliance's user interface. It provides the buttons and display you press to select cycles and options, restoring normal control and appearance when the original panel is damaged or unresponsive.

• Houses the user interface buttons and labels used to select cycles and settings
• Protects and positions the UI components on the front of the appliance
• Helps address issues like missing or cracked panel, worn/illegible buttons, or stuck keys
• Resolve unresponsive controls when failure is due to a damaged panel assembly

• Disconnect power before servicing to avoid electrical shock
• Open the door and remove mounting screws to access the console
• Transfer any attached UI board/wiring only designed to be reused; handle electronics with care
• Button alignment and secure all fasteners before restoring power

The Insulation is an OEM part for Frigidaire dishwashers. It is designed to reduce sound during wash cycles and help create a quieter dishwasher experience. The sound insulation minimizes noise transmission by absorbing and dampening vibrations throughout washing.

Causes of bad sound insulation can include breakdown of insulating materials over time, compression that reduces soundproofing density, or water damage or impacts.

Symptoms of bad sound insulation include:

• Noticeably louder operations with minimal sound dampening
• Rattling, banging, or buzzing sounds emanating from the appliance
• Transference of vibrations that causes adjacent cabinets to resonate

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

• Monitors water clarity/soil level during the wash
• Sends feedback to the control to adjust cycle length, rinses, and heating
• Failure can cause very long or very short cycles
• Can trigger sensor-related fault indications

• Disconnect power at the breaker and shut off water before servicing
• Access the sensor from the bottom near the sump; remove the toe panel if needed
• Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
• Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This cover is a protective panel used on Frigidaire appliances to shield and finish a specific assembly. Replacing a cracked or missing cover helps protect internal components and maintain proper routing or airflow so the unit operates as intended. What it does

• Shields internal parts from dust, moisture, and accidental contact
• Helps guide airflow or water within the assembly
• Secures adjacent components and restores a clean, finished appearance
• Typical symptoms: cracks, broken tabs, looseness/rattling, warping, or a missing panel

• 1 cover

• Disconnect power; if the appliance uses water, also shut off the supply
• Note fastener locations and transfer any clips or inserts from the original cover
• Inspect mating surfaces and any seals; replace damaged seals if needed
• Do not overtighten screws; verify clearances and wire routing before restoring power

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

The Dishwasher Manifold is an OEM part for Frigidaire dishwashers. It is a complex component that controls the flow of water through the various spray arms and nozzles within the dishwasher.

Causes can be mineral buildup or sediment that disrupts water flow, cracks or leaks in internal waterways, or damage from impact or unbalanced loads.

Symptoms of a bad Manifold include:

• Inadequate water pressure to one or more spray zones
• Blocked or clogged spray nozzles or arms
• Insufficient water flow for proper cleaning

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Panel is an OEM part for Frigidaire dishwashers. Located at the front of the dishwasher door, the control panel features buttons and displays that allow for the selection and monitoring of wash cycles. Printed electronic circuits distribute input signals to initiate the appropriate cycle settings.

Causes of a bad Control Panel can include cracked or damaged screens, non-responsive buttons, or failures of internal electronic pathways over time. 

Symptoms of a bad Control Panel include:

• Faulty or unreadable display screens  
• Random cycle activation without input
• Repeated error codes or flashing lights
• Physical damage or loose components  

This genuine OEM Frigidaire part is compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models as well.

The Control Board is an OEM replacement part for Frigidaire dishwashers. Located inside the cabinet behind the control panel, the control board utilizes integrated circuits and electronic components to regulate all dishwasher functions. It receives input signals from the control buttons to initiate and monitor the wash cycle. 

Causes of a bad control board can include failures of electronic components over time, voltage fluctuations that cause circuit damage, or moisture infiltration leading to corrosion.

Symptoms of a bad Control Board include:

• Dishwasher fails to start or stops mid-cycle unexpectedly
• Lights or displays on control panel malfunction  
• Inability to select options or cycles
• Complete non-responsiveness of control functions

This board is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

This replacement screw secures appliance components so panels, brackets, and trim stay tight and properly aligned. Replace a missing, stripped, or corroded fastener to restore a solid fit and help stop vibration or rattling.

• Fastens components to the chassis or assembly for correct fit
• Helps maintain alignment and reduce movement and noise during operation
• Restores secure mounting when original hardware is missing, rusted, or stripped
• Typical symptoms: loose panel or handle, rattling noises, hardware backing out

• Disconnect power; if servicing a dishwasher, also shut off water
• Match the screw to the original location before installation
• Start threads by hand to avoid cross-threading, then tighten snugly without overtightening