Flce7522aw4 Parts

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

Ceramic dryer heating element terminal block.

This control panel is the appliance's front user interface, replacing a cracked, faded, or non-functioning console to restore a clean appearance and reliable control operation. It fits into the range/oven console and accepts the overlay and switches. What it does:

• Provides the front surface and mounting for the oven/range controls and display
• Restores a secure mounting point when the original panel is cracked, bent, or missing
• Can resolve cosmetic issues and stop loose or rubbing controls from sticking
• Helps prevent debris from reaching internal electronics behind the console

• Disconnect power to the appliance before beginning any work
• Removal typically requires unscrewing trim and console fasteners; handle edges carefully
• Keep small screws and clips organized for reassembly; some panels use snap clips that can break if forced

This idler arm assembly restores proper dryer belt tension so the drum turns smoothly and reliably. It replaces a worn or damaged tension arm to help eliminate belt slipping and abnormal noise. What it does:

• Acts as the dryer belt tensioner to keep the drive belt properly seated on the drum and motor pulley
• Prevents belt slipping that can cause the drum to stop turning or to turn intermittently
• Reduces squealing, grinding, or rubbing noises caused by a worn or loose idler
• Helps extend belt life by maintaining correct alignment and tension

• One idler arm assembly

• Disconnect power to the dryer before starting any repair
• Access may require removing the dryer front or rear panel depending on model
• Inspect the belt and pulley(s) while replacing the arm; replace worn belts or pulleys as needed

A small locating pin used to align and secure parts during assembly, helping panels and components sit correctly for reliable operation. Ideal when a worn or missing pin causes fit or alignment issues. What it does:

• Positions and holds panels, trim, or assemblies in the correct location during reassembly
• Prevents shifting or misalignment of covers and access panels
• Restores proper fit where a bent, broken or missing pin causes loose trim or gaps
• Small, simple replacement that addresses common fit/fitment symptoms

• Disconnect power and unplug the appliance before beginning any work
• Use basic hand tools; avoid forcing parts into place to prevent damage
• Inspect surrounding components for damage and replace if worn

Pan hd phillips ,6-32 x 0.337 ,dog point

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

This replacement control panel restores the user interface and appearance of your appliance's console, providing a clean mounting surface for buttons, knobs, and the display so controls operate reliably and look like new. What it does:

• Houses the control buttons, selector switches, and display area used to operate the appliance
• Replaces cracked, faded, or cosmetically damaged panels to improve appearance
• Helps remedy problems where buttons stick, feel loose, or no longer register presses
• Provides the proper mounting and alignment for switches and electronic components

• Disconnect power to the appliance before beginning any repair.
• Remove surrounding trim or console screws to access and replace the panel; some models require transferring switches or displays from the old panel.
• Handle edges carefully and avoid touching exposed circuitry or contacts.

This housing assembly replaces the outer cabinet that supports and protects internal components, restoring proper fit and appearance. It's a direct-replacement body piece designed for safe, stable operation. What it does:

• Provides structural support for internal parts and mounting points
• Protects wiring, controls and internal components from debris and damage
• Restores proper alignment and enclosure fit to reduce vibration and rattling
• Helps maintain correct airflow paths and component spacing

• Disconnect power (unplug or shut off breaker) before beginning any work.
• Use appropriate hand tools; remove panels and fasteners to access mounting points.
• Watch for sharp edges and handle the housing carefully to avoid damage or injury.
• Secure all fasteners during reassembly; replace any damaged clips or screws.

The Leveling Leg is an OEM component specifically designed for Frigidaire washers. These adjustable legs properly mount and balance the washer on varied floor surfaces within specifications.   

Symptoms of a damaged leveling leg include:

• Excessive vibration during wash and spin cycles
• Abnormally loud operation noises 
• Difficulty opening and closing the washer door

Causes can include deterioration of internally threaded plastic rods over repeated adjustments. Frigidaire engineers leveling legs as a wear item to preserve smoother cycles.

This OEM Frigidaire part is also compatible with Kenmore, crossed references to Electrolux brands may not apply. Leveling aids proper support under heavy drum motions and balanced spin extraction for vibration reduction. Replacing compromised legs restores stable platform balance as designed.