Flcg7522aw2 Parts

This sensor monitors appliance conditions and relays a signal to the control so heating, cooling, or cycle functions occur at the right time. Replacing a failing sensor restores accurate feedback and more reliable operation.

• Detects operating conditions and sends signals to the control board
• Helps regulate heating/cooling output or cycle timing
• Common symptoms of a failed sensor: erratic operation, incorrect readings, cycles that won't start/finish, or related error codes
• Restores proper control feedback when the original is damaged or out of range

• Disconnect power to the appliance before servicing
• Access the sensor per your service manual; note wire colors/orientation and connector locks before removal
• Transfer any mounting clips or brackets from the original if required
• After installation, run diagnostics or verify resistance/continuity per the tech sheet to confirm proper operation

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Valve is an OEM part for Frigidaire washing machines. It is responsible for regulating the flow of water into the washer tub and hoses during all cycles. The water valve allows cold, warm, or hot water to pass through depending on the settings and ensures the proper amount is distributed for optimal cleaning performance.

Causes of a bad water valve can include mineral buildup over time, worn or damaged internal components that interfere with water flow regulation, or issues with the electronic control board that operates the valve.

Symptoms of a bad water valve include:

• Inability to select warm or hot water temperatures
• Poor or inconsistent water temperature
• No water filling or slow water filling during the wash cycle
• Water leaks from the valve area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This glow-bar igniter lights the gas burner in your dryer so it can produce heat. When the igniter is cracked, weak, or open, the burner won't light and clothes won't dry properly.

• Heats up to ignite the gas burner during each heating cycle
• Common symptoms of failure: no heat, takes too long to dry, burner won't light, igniter doesn't glow or glows but no flame
• Restores consistent ignition and drying performance

• Unplug dryer and shut off gas supply before servicing
• Handle the igniter carefully—ceramic element is fragile; avoid touching it with bare fingers
• Note wire routing and burner alignment before removal
• After installation, restore gas/electric and check for proper burner ignition

The Gas Valve is an OEM part for Frigidaire dryers. It is a component that controls the flow of gas to the burner during the drying cycle. The gas valve regulates the amount of gas delivered based on cycles, selected temperatures, and dryness settings.

Causes of a bad gas valve can include wear and tear over time that causes seals to crack or oxygen sensors to malfunction, allowing gas to escape or leak.

Symptoms of a bad gas valve include:

• Delayed or slow drying times
• Uneven drying results
• Strange smells coming from the dryer
• The dryer fails to ignite or stay lit
• Excessive amounts of lint in the lint trap

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Belt is an OEM part for Frigidaire combination washer/dryer laundry centers. It refers to the elastic overdrive belt that circulates mechanical rotation from the drivetrain motor to the washing tub and drum inside.  

Located inside the hidden motor compartment, this V-belt transmits high-torque oscillating or spinning motion through changes in the transmission clutch mechanism. Proper belt tension is critical for engaged operation between motor and drum.

Causes for belt damage or failure include cracks developing over extended use, drying/hardening from heat exposure, or slipping off motor pulleys from stretching or wear over time.

Symptoms include: 

• Drum or agitator failing to turn during cycles
• Abnormally loud clanking/squealing noises from inside  
• Tripped overload on the motor due to overtaxed movement

Replacing the belt with a Frigidaire OEM part restores smooth power transmission for thorough, dependable cleaning cycles. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore combo laundry units.
 

The Suspension is an OEM part for Frigidaire top-loading agitator washing machines. It refers to springs and vibration-dampening mounts underneath the wash tub. 

These components absorb mechanical stresses from unbalanced loads and support the heavy rotating assembly without added noise transfer to adjacent surfaces. Keeping tub components properly isolated is important for structural integrity over many years.

Symptoms of a worn suspension include: 

• Visible movement and shaking of the entire machine on top of the unit  
• Screeching or screeching noises when agitating heavy loads
• Fastener screws backing out or washing tub no longer level

Replacing with Frigidaire OEM suspension parts renews shock absorption to maintain steady cycles and protect connected plumbing. This is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore top load models.
 

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

This safety thermostat is a temperature-sensitive switch that helps protect your appliance from overheating. When excessive heat is detected, it opens the circuit to stop power to critical components, helping prevent damage and ensuring safe operation.

• Monitors temperature at a specific location and interrupts power if it exceeds a safe limit
• Can cause no power, no heat, or shutdown during use when failed or tripped
• Helps prevent overheating damage to internal components
• Restores normal operation when replaced

• Disconnect power to the appliance before service
• Note wire positions and terminal orientation before removal
• Use proper tools and avoid bending or stressing terminals
• After installation, check for underlying overheating causes (blocked airflow, failed fan, etc.)

The Pulley Assembly is an OEM part for Frigidaire washing machines. This assembly contains the pulleys that power the tub rotation during wash cycles.

Causes of a bad pulley assembly include wear from years of cycles, broken belts that have damaged the pulleys, rust from water exposure, or physical damage such as dents in moving parts. Overloading hampers even movement.

Symptoms of a bad pulley assembly include:

• Tub unable to turn or agitate clothes during cycles
• Grinding or squealing noises coming from a seized pulley
• Unable to load heavy items due to lack of normal agitation
• Pulley fasteners loosened or sheared away from the assembly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

This replacement housing is the body that holds the washer's detergent drawer and channels rinse water through each compartment into the tub. Replacing a cracked or warped housing restores proper dispensing and helps prevent leaks at the dispenser area.

• Supports and aligns the detergent/bleach/softener drawer
• Routes incoming water to flush each compartment into the wash tub
• Interfaces with inlet hoses and outlet chute for proper flow
• Common symptoms: water leaking from the dispenser/front panel, detergent or softener left in the drawer, poor dispensing, drawer difficult to open/close

• Disconnect power and shut off water supply before servicing
• Remove necessary panels/trim, pull out the drawer, and release mounting screws/clips to access the housing
• Label and disconnect hoses; note routing. Transfer any reusable siphon caps, seals, and the drawer from the original housing
• Reassemble, restore water and power, and run a test fill to check for leaks

The Transmission is an OEM part for Frigidaire combination washer/dryer laundry centers. It refers to the primary mechanical component that allows the center agitator or drum to spin during wash and spin cycles.

Located inside the base of the drum housing, the transmission engages via motor pulley action to oscillate or rotate container contents as needed. Smooth operation is critical for balanced spinning that removes excess water without damaging fabrics. 

Causes of transmission issues include worn gears from age, lubrication failure, or shifting/linking mechanism damage from excessive loads.

Symptoms of a failing transmission include: 

• Excessive vibration or shaking noisily during spin cycles
• Limited or no agitation or rotation of the drum  
• Belts continuously slipping off motor pulleys

Replacing with a Frigidaire OEM transmission restores dependable wash and spin cycles. This keeps laundry moving as designed for thorough cleaning results. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore combo units.
 

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.