Fphdz491kfo Parts

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

• Monitors water clarity/soil level during the wash
• Sends feedback to the control to adjust cycle length, rinses, and heating
• Failure can cause very long or very short cycles
• Can trigger sensor-related fault indications

• Disconnect power at the breaker and shut off water before servicing
• Access the sensor from the bottom near the sump; remove the toe panel if needed
• Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
• Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

This seal kit restores a tight, insulated barrier around a window air conditioner. Replacing worn or missing seals helps block gaps and drafts, reduce noise and vibration, and maintain efficient cooling performance.

• Creates an air-tight barrier between the unit, sash, and window frame
• Helps reduce warm air infiltration, dust, and insects entering around the A/C
• Supports proper cooling by minimizing recirculation of hot outdoor air
• Helps resolve drafts, reduced cooling, condensation at the cabinet, or rattling noises

• Unplug the unit before servicing; work on a cool appliance
• Remove old foam and adhesive; clean and dry surfaces before applying new seals
• Measure and cut seals to length; avoid stretching or compressing the foam during install
• Press firmly to ensure full contact; follow your model's installation guide for placement

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This spray arm assembly distributes high-pressure wash water inside the dishwasher and spins to cover the racks. Replacing a cracked or clogged arm restores proper spray coverage for cleaner dishes and consistent wash performance. What it does:

• Rotates as water flows to spray dishes evenly across the tub
• Channels water from the circulation pump through precision jets
• Helps resolve poor cleaning results or spots left on dishes
• Addresses issues like a spray arm that won't spin, clogged nozzles, or visible damage

• 1 spray arm assembly

• Disconnect power at the breaker and turn off the water supply before servicing
• Remove the rack if needed to access the arm
• Release the locking tabs or unthread the retaining cap to remove the old arm
• Seat the new arm fully, secure the retainer, and confirm it spins freely before a test cycle

The Drain Pump is an OEM part for Frigidaire dishwashers. It is responsible for removing water from the dishwasher tub at the end of each cycle. The drain pump works in conjunction with the drain hose to efficiently expel dirty water and ensure dishes are thoroughly dried.

Symptoms of a bad drain pump include:

• Water not fully draining out of the bottom of the dishwasher tub
• Puddles or standing water left inside after a cycle is finished
• Mildewy or musty smells emitting from the appliance
• Loud or grinding noises coming from the drain pump motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Restore a secure, reliable door closure. This replacement door latch engages the door mechanism so the appliance recognizes the door is closed and can operate as intended, preventing nuisance "won't start" issues caused by a broken latch. What it does:

• Keeps the door closed and properly aligned with the catch
• Engages the door mechanism/switches so the unit can run when shut
• Replaces worn or broken latch hook tabs
• Common symptoms: door won't close or stay latched; unit won't start; must push/hold door to run; visible broken latch hook

• 1 door latch

• Disconnect power before servicing; wear cut-resistant gloves
• Access the door's inner panel/trim to reach the latch; protect glass and finishes
• Note spring/clip orientation if present and transfer any reusable hardware
• Test door latching and proper operation before final reassembly

This adjustable leveling leg threads into the appliance base to support and stabilize the unit. Replacing a worn or missing foot restores proper leveling for smoother operation, better door alignment, and reduced vibration.

• Provides height adjustment to level the appliance on uneven floors
• Helps keep the unit stable to minimize rocking and rattling
• Improves door alignment and closure when the cabinet is properly leveled
• Replaces a cracked, stripped, or missing leg

• Disconnect power; if your appliance has a water line, turn off the supply and carefully move the unit to access the leg.
• Support the appliance to relieve weight; unthread the damaged leg and start the new leg by hand to avoid cross-threading.
• Adjust height by turning the foot; use a level to ensure the cabinet is plumb and stable.
• Tighten carefully and recheck stability after the appliance is set back in place.

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This heater assembly restores heat production in electric dryers so clothes dry efficiently. It replaces a failed heating element and helps return the appliance to normal drying performance. What it does:

• Heats air passing through the dryer drum so laundry dries during operation
• Replaces a burned-out or open heating element that causes no heat or weak heat
• Addresses long dry times and extended cycles when the element isn't functioning
• Works with the dryer's blower and thermostatic controls to maintain proper air temperature

• Disconnect power at the breaker before starting any repair; this part carries live voltage during operation
• Handle the heating element carefully to avoid bending or damaging the coil
• Inspect fuses, thermostats, wiring, and connectors while replacing the heater to ensure full repair
• Follow the appliance manufacturer's service instructions for disassembly and reassembly

This dishwasher sump assembly houses the pump path and turbidity sensor that helps the machine detect water clarity for proper wash cycles. Replaces a worn or damaged sump to restore draining and turbidity sensing. What it does:

• Circulates and directs wash and drain water through the pump housing
• Houses the turbidity sensor that helps the control detect soil level for cycle adjustment
• Helps prevent leaks and maintains correct water flow for cleaning performance
• Can resolve symptoms like poor draining, error codes related to turbidity or water quality sensing, and reduced wash performance

• Disconnect power and water supply before attempting service; follow factory service instructions
• Inspect seals and mounting gaskets; replace any brittle or damaged gaskets to ensure a watertight fit
• Handle the turbidity sensor carefully and avoid contaminating the sensing surface

Replacement screw that secures trim, panels and internal components to restore proper fit and reduce rattling. Use when a fastener is missing, stripped, or corroded to help maintain stable, safe appliance operation. What it does:

• Secures panels, trim, brackets or other appliance parts to prevent looseness or movement.
• Replaces missing, worn, or damaged screws so components align and operate correctly.
• Helps reduce rattling, vibration noise, and gaps around doors or panels.
• Verify the exact size and thread before ordering to ensure proper fit.

• Disconnect power and water before starting any repair.
• Use the matching screw size and thread; do not force or overtighten.
• Start threads by hand to avoid cross-threading; use the correct screwdriver or bit.
• If threads or mounting holes are damaged, repair before reuse.

The Mounting Bracket is an OEM part for Frigidaire dishwashers. It is a metal component that secures the dishwasher to the surrounding cabinetry. The mounting bracket provides structural support and stability during operation.

Causes of a bad mounting bracket can include damage from installation/removal, cracks or deformities from heavy loads, or broken welds/fasteners holding it in place.

Symptoms of issues with the mounting bracket include:  

• Excessive vibration or shaking of the dishwasher during cycles
• The unit not sitting level or secured properly in the space
• Noises related to movement that shouldn't occur
• Visible damage or instability of the unit 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present