Frs26znh Parts

This defrost heater melts frost and ice build-up on the evaporator to restore normal airflow and cooling. Replacing a failed heater helps prevent recurring frost and improves temperature consistency in the freezer compartment. What it does:

• Heats the evaporator coil during the defrost cycle to remove accumulated frost and ice.
• Restores proper airflow and cooling when frost buildup is preventing normal operation.
• Common symptom: visible frost/ice on evaporator or evaporator cover.
• Common symptom: freezer running but cooling inconsistently or icing up.

• Disconnect power to the appliance before starting any repair.
• Inspect and replace only with the exact part number; handle the heater element carefully to avoid bending or damage.
• Reinstall evaporator cover and any seals; test a complete defrost cycle after replacement.

This grille clip is a small plastic retainer that secures a refrigerator grille or trim piece to the cabinet, keeping the front panels aligned and preventing rattles or gaps for a tidy appearance. What it does:

• Secures the lower/front grille or trim to the appliance cabinet to hold it in place
• Prevents grille movement, rattling, or sagging that can occur with worn clips
• Helps maintain a tight fit between trim and cabinet for a finished look
• Simple replacement part when existing clip is cracked, broken, or missing

• One grille clip

• Typically snaps into place; inspect mating slot and clip orientation before installing
• Replace any damaged adjacent clips for even support and fit
• Work carefully to avoid damaging the grille or surrounding trim

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear where wiring, rods or panels pass through mounting openings. It helps keep parts aligned and protects against chafing and noise. What it does:

• Cushions and isolates vibration between moving parts and chassis
• Protects wiring, tubes or rods from rubbing and abrasion at mounting holes
• Helps reduce noise caused by contact or metal-on-metal vibration
• Aids in maintaining proper part alignment and secure fit

• Grommet

• Inspect mating hole and surrounding area for debris or sharp edges before installing
• Fit the grommet into the mounting hole so the flange seats evenly on both sides
• Replace any damaged or excessively worn grommets to restore protection
• Disconnect power and follow appliance safety procedures before attempting service

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

A replacement refrigerator light socket that holds and connects the interior bulb so the light turns on when the door opens. Restores reliable interior lighting for easier food visibility and maintenance. What it does:

• Holds the interior refrigerator bulb and provides the electrical connection to power the lamp
• Replaces a cracked, burned, loose or intermittently working socket
• Helps stop flickering, arcing, or loss of interior light due to a damaged holder
• Works with the refrigerator's existing wiring and bulb type

• Disconnect power to the appliance before starting any repair
• Handle the bulb carefully; remove it before replacing the socket
• Verify proper wire connections and secure mounting; restore power and test the light after installation

The coconut carbon filter media reduces unpleasant tastes and odors while removing sediments like dirt and rust. It features a powerful 0.5 micron rating that removes particles invisible to the naked eye. For optimal performance and efficiency, the filter should be changed every 6 months or 300 gallons, depending on use. Flow Rate: 0.5 gpm. Operating Pressure: 20 - 140 psi. Operating Temperature: 33 - 100 °F. Meets NSF Standard: 42. Approved for WQA Gold Seal. Fits most Frigidaire and Kenmore (with model prefix 253) refrigerators made before 2001. Color: white. This filter measures about 2 inches in diameter by 4 inches high. 2 pack. For a single pack order wfcb.

Left hand side. For the right hand side order 241674402

This is a replacement screw used to secure panels, trim and other appliance components to restore proper fit and reduce rattling. It matches the OEM part form and fastening function for compatible Frigidaire appliances. What it does:

• Secures panels, brackets or trim to maintain proper alignment and appearance
• Replaces missing, stripped or damaged screws that cause loose parts or vibration
• Helps prevent rattling and keeps components seated for safe operation
• Restores original fastening where a worn or corroded screw failed

• Disconnect power to the appliance before beginning any repair to avoid electrical hazard
• Use the correct screwdriver or driver bit and hand-start threads to avoid cross-threading
• Tighten until snug; avoid overtightening which can strip threads or damage panels
• If thread damage is present, replace with the correct OEM fastener (do not force)

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

This cantilever shelf clip secures a refrigerator cantilever shelf in place so shelves stay level and stable. It replaces a cracked or missing clip to restore proper shelf support and prevent shifting or slippage. What it does:

• Holds the cantilever shelf bracket/tier in the refrigerator liner to keep the shelf properly positioned
• Prevents shelf from tipping, sliding, or falling when items are placed on it
• Replaces worn, cracked, or broken clips that no longer grip the shelf brackets
• Works with standard cantilever-style shelving systems used in many refrigerators

• One cantilever shelf clip

• Remove food and glass shelves/trim as needed for safe access before replacing the clip
• Align clip with the shelf bracket slot and press firmly until it snaps into place; do not force beyond normal fit
• Handle glass shelves carefully to avoid breakage; wear gloves and eye protection if needed