Frss2vaf20 Parts

This small bearing fits into the upper door hinge assembly of a refrigerator or freezer door, allowing the door to pivot smoothly when opened and closed. It sits between the hinge pin and the door bracket to reduce friction and wear. Replace this bearing if the door feels stiff, squeaks when opening, or doesn't close evenly.

Fix a refrigerator that won't cool or runs constantly with this inverter compressor. Advanced repair requiring refrigerant handling certification.

Replacement door handle for refrigerator doors. Restores secure grip when original is cracked, broken, or loose. Direct-fit exterior handle part.

This is the plastic housing that holds the air filter inside the refrigerator compartment. It secures the air filter in place so it can effectively remove odors and keep the interior air fresh. Replace this housing if it is cracked, broken, or no longer holds the air filter securely in position.

Replacement cabinet trim for side-by-side refrigerators. Conceals exposed edges and gaps for a finished look. Installs at exterior panels. Replace if cracked, broken, or missing.

Fix a refrigerator that won't cool, has non-responsive controls, or won't power on. This electronic control board manages all electrical functions. DIY-friendly.

This is the bottom hinge assembly that supports the lower pivot point of the refrigerator door. It bears the weight of the door and allows it to swing open and closed smoothly. Replace this hinge assembly if your refrigerator door sags, doesn't close properly, or if the hinge pin or mounting bracket is worn or damaged.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Supports refrigerator crisper or bin drawers for smooth gliding. Replace when drawers stick or bind. Confirm fit with your model number listed.

Genuine mounting screw secures panels, brackets, and covers inside your refrigerator. Replace missing, stripped, or corroded fasteners to restore secure fit.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Refrigerator motor bushing that surrounds the motor shaft to reduce vibration. Replace if worn, damaged, cracked, or missing to restore smooth operation.

This is an auger motor located in the freezer compartment that drives the auger mechanism to push ice from the ice bin to the dispenser chute. It activates when you press the ice dispenser lever or paddle on the door. Replace this motor if ice has formed in the bin but nothing comes out when dispensing, the dispenser makes no sound, or you hear the motor humming but ice does not move forward.