Gcrg3060af Parts

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Note: ONE screw only, order as needed.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This fan motor drives your oven's convection fan, circulating hot air for even, reliable cooking performance. Replacing a weak or noisy motor restores proper airflow to reduce hot spots and improve convection baking and roasting results. What it does:

• Powers the rear convection fan to move air across the oven cavity
• Promotes more uniform temperatures on multiple racks during convection cycles
• Helps the oven maintain stable heat during use
• Common symptoms: fan won't spin, intermittent or slow rotation, loud humming/scraping from the rear, uneven results in convection mode

• 1 fan motor

• Disconnect power to the range or wall oven before servicing
• Access may require removing the rear panel or the oven's rear cover; note wire locations for reassembly
• Transfer the original fan blade and mounting hardware to the new motor; handle sharp edges and avoid bending the blade
• Spin the blade by hand to ensure free movement before restoring power

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This control mounting hex nut secures the burner or oven control to the control panel, keeping the shaft stable so the knob turns smoothly and the switch stays properly aligned.

• Threads onto the control/infinite switch or thermostat bushing to fasten it to the panel
• Prevents the control from rotating or shifting when the knob is turned
• Replace if the original nut is missing, stripped, rounded, or corroded
• Common signs: loose or wobbly knob, switch spins in the panel, or misaligned knob indexing

• Disconnect power; for gas appliances, also shut off gas before servicing
• Pull off the knob and any trim; support the control body from behind the panel while removing/installing the nut
• Start the new nut by hand to avoid cross-threading; tighten snugly with the correct-size wrench—do not overtighten
• The control sits square in the panel and the knob operates smoothly before restoring power

The Handle is an OEM part for Frigidaire ranges. Crafted from durable heat-resistant metal, these handles provide safe, ergonomic access to oven interiors during cooking cycles.  

Prolonged exposure to elevated oven temperatures causes typical discoloration of painted finishes as well as looseness from load stresses reducing tactile control over years. Cooking convenience decreases without gripable surfaces.

Symptoms indicating handle wear include:

• Faded, chipped, or flaking handle finishes  
• Loose, rattling, or awkward movement from placement
• Deteriorating mounting attachments risking accidental falls

Replacing with this OEM Frigidaire handle restores tactile guidance into the cooking cavity. Compatibility also fits some Kenmore, Electrolux, and Gibson ranges renewing secure doorknob function through authorized maintenance. 

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

This cooktop grate replaces a damaged or worn grate on your gas range or cooktop. It supports pots and pans securely over the burner to maintain a stable, level cooking surface and safe, consistent heating.

• Sits above the surface burner to hold cookware at the proper height
• Provides a stable surface to reduce pan wobble, rocking, or tipping
• Replaces grates that are cracked, broken, heavily rusted, or warped
• Helps protect the cooktop from direct flame and cookware contact

• Turn all burners off and allow the cooktop and grate to cool completely before handling
• Lift off the old grate and clean debris from the support pads or recesses
• Set the new grate in place, ensuring all feet sit flat and it's centered over the burner(s)
• Check pan stability before cooking

This manifold supply tube routes gas from the appliance's inlet/regulator to the burner manifold and valves. Replacing a damaged tube helps restore safe, consistent fuel delivery and reliable burner performance. What it does

• Channels gas from the regulator/inlet to the burner manifold/valve assembly
• Maintains proper fuel flow to multiple burners
• Replace if the tube is bent, cracked, corroded, or leaking
• Symptoms can include multiple burners not lighting or weak/uneven flames due to restricted flow

• 1 manifold supply tube

• Shut off the gas supply and disconnect electrical power before servicing
• Note the routing and orientation of the original tube to match bends and connections
• Use only approved practices for your fitting type; do not apply sealant to flare-seat connections
• After installation, perform a soap-and-water leak test on all joints; do not operate if bubbles appear

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

The Control Board is an OEM component specifically designed for Frigidaire electric ranges. As the processing center, it regulates oven temperatures, timers, surface heating elements, and diagnostic functions. 

Symptoms of a faulty control board include:

• Inability to turn stove top burners or oven on
• Temperature controls not accurately sense or setting heat 
• Codes appearing for malfunctions in logic circuits

Causes of a bad control board can include general wear from repeated thermal cycling. Potential spills on cooktops pose threats to sensitive semiconductor chips.

This OEM Frigidaire part is also compatible with Electrolux, Crosley, and some Kenmore models. Replacing restores reliable operation of all temperature calibration and safety protections as intended by the manufacturer. Maintaining control boards prevents disruptive breakdowns.