Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.
Not hard when you have videos and a mechanical background....piece of cake.... Read more
Replaces the front outer tub cover that houses the door boot seal and aligns the spin basket. Order a new cover if yours is cracked or worn from use.
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more
This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.
I replaced the transmission, and a few other parts associated with the transmission. Read more
12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.
The auger motor failed and wouldn't turn. I replaced the motor and it works without a problem. Make sure you dont throw away the motor boot or buy one if you don't have one. Otherwise, the temperature will freeze up the motor and lead to premature failure. Read more
Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.
Size: 14-10 a trt 7/8 s.
Replaced the hub nut, tub bearing split ring, tub seal, hub washer and agitator coupler. I watched multiple times the APP video. It was extremely helpful and I would not have attempted this without seeing the video. I had a lot of trouble getting the hub nut off. I used an 1 5/8" 6 point strike box wrench and a 4# hammer to get it off. I sprayed it with WD 40 5 or 6 times over of the course of a week to let it soak. I finally got it off. Had I known that the shaft is not round I would have... Read more
8-18 hi/lo 5/8
Includes 12 screws.
Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.
Fix a washer that won't spin or hums but doesn't start. This single-speed motor replacement restores spin cycles when the motor windings fail.
First I cleaned out the pressure switch line that allows the motor to kick into gear when the water level is low enough to start the spin cycle. Second, I determined the motor was worn out and could not spin the drum so I order a new motor from Appliance Parts. They had the part in stock and it was shipped out promptly. Third, opened the front of the washing machine to access the motor, removed 4 huts from the under carriage, unplugged the electrical connection to the motor, removed and... Read more
This is the rear-mounted control panel assembly for a washing machine. It houses the cycle selector knobs, buttons, and associated wiring that allow you to choose wash settings. Replace this panel if the controls are unresponsive, the panel is cracked or damaged, or the labeling is worn and unreadable.
I took of the backsplash and took the hose off of the pressure switch and accidently broke off the stem of the pressure switch and the catch parts of the pressure switch. I put some Krud Cutter into the pressure switch hose and blew into it until I got air to flow. I stopped the tub from over flowing and replace the pressure switch and backsplash. Read more
Fix washer leaks or no water flow with this water inlet connector hose. Routes water from valve to dispenser. Direct-fit replacement for worn hoses.
Washer won't advance through cycles or drains at the wrong time? This timer controls cycle sequencing through wash, rinse, and spin steps. DIY repair.
Replaced the Timer We bought the part over the phone with appliance parts pro they were super nice shipping was fast!!! Thanks so much!!! Read more
Size: 8-32 t. Includes 12 screws.
Fix leaks at the water inlet with this hose connector. Restores a secure, watertight connection between the fill hose and washer inlet for normal cycles.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.