Ge Cgs990setss Parts

This Range Cooktop Bracket secures the main top to the appliance frame for a tight, stable fit. Replacing a bent or missing bracket can correct a loose, misaligned, or rattling cooktop and help it sit flush.

• Secures the main cooktop to the chassis to prevent lifting or shifting during use
• Helps maintain proper alignment and a flush fit with surrounding trim
• Common symptoms include a loose or uneven cooktop, rattling, or visible gaps
• Useful when the original hold-down bracket is bent, missing, or damaged

• Disconnect power; for gas ranges, shut off the gas supply before servicing.
• Support the cooktop while replacing the bracket; beware of sharp edges.
• Reuse manufacturer-specified fasteners where applicable and tighten securely without overtightening.

This broil element is the oven's upper heating element that produces the direct, high heat used for broiling and browning. Replacing a faulty element restores proper broil performance and even browning on foods. What it does:

• Heats from the top of the oven to brown and broil food
• Supplies concentrated, high-temperature heat for searing and finishing dishes
• Common symptom: oven broil does not heat or produces little to no heat
• Common symptom: food browns unevenly or element shows visible damage or breaks

• Disconnect power to the appliance at the breaker or unplug before servicing
• Access typically requires removing the oven inner panel or broil cover; retain mounting screws
• Handle the element carefully to avoid bending or damaging terminals

This valve control assembly routes gas to the surface burners and regulates flow as you turn the knobs. Replacing a worn manifold restores smooth flame adjustment and consistent burner performance on your gas range or cooktop.

• Directs incoming gas through the manifold to each surface burner valve
• Opens and closes with the control knobs to set flame height
• Works with the ignition system for steady lighting and operation
• Typical symptoms: burner won't receive gas, flame won't adjust, or a stiff/hard-to-turn valve

• Disconnect power and shut off the gas supply before service; allow the appliance to cool
• Label and disconnect gas tubing and any wiring from the old assembly; transfer mounting hardware as needed
• After installation, restore gas and check all joints with an approved leak-detection solution (never an open flame)
• Verify each burner lights and adjusts smoothly; recheck for leaks

This top burner injector assembly delivers gas from the manifold to a range's top burner for controlled ignition and stable flame. It restores proper fuel flow so burners light reliably and maintain even heat for cooking. What it does:

• Directs gas to the top burner so the burner can ignite and produce a steady flame
• Helps correct low or uneven flame at a single top burner
• Replaces a clogged, damaged, or worn injector that can prevent ignition or proper burner performance
• Works as the burner-side metering piece in the gas delivery path

• One top burner injector assembly

• Turn off the gas supply and power to the appliance before servicing
• Only install the exact replacement part for your model; tighten fittings per manufacturer guidance
• Check all seals and connections for leaks after installation; use soapy water or a gas leak detector

This 10-32 mounting screw secures appliance handles and trim pieces, restoring proper fit and preventing loose or wobbly handles. Use it when a handle feels loose or the attachment hardware is missing or damaged. What it does:

• Fastens handles and related trim to appliance doors or panels
• Restores secure attachment to stop handle wobble or movement
• Replaces stripped, worn, or missing mounting hardware
• Matches OEM thread size for proper fit in mating fastener holes

• One 10-32 mounting screw

• Use the correct screwdriver or bit to avoid stripping the screw head
• Start threading by hand to ensure proper alignment before tightening
• Tighten until snug; avoid overtightening which can strip threads or crack panels
• Disconnect power and follow appliance safety instructions if disassembly exposes electrical components

This small rubber grommet cushions and secures a range or oven door handle, helping keep the handle stable and reducing wear where the handle meets the door. It restores a snug fit and quiet operation. What it does:

• Acts as a protective bushing between the handle and door to prevent metal-on-metal contact
• Helps stop a loose, wobbly, or rattling handle
• Reduces wear on mounting holes and finish around the handle
• Provides a tight, vibration-dampening fit for the handle assembly

• Disconnect power to the appliance before starting any work
• Typically a simple press-fit replacement; handle removal may be required for access
• Inspect surrounding fasteners and mounting surfaces; replace damaged parts as needed

This cast center grate replaces a damaged or missing mid grate on compatible gas cooktops, restoring stable support for cookware and even heat distribution at the cooktop center. Durable cast construction matches OEM fit and appearance. What it does:

• Supports pots and pans over the center burner for steady, level cooking
• Restores proper burner-to-grate alignment to help prevent wobbling or tipping
• Replaces cracked, chipped or worn center grate surfaces that can catch spills
• Helps maintain safe cookware contact so burners perform as intended

• One (1) cast center grate

• Only replace when cooktop and burners are completely cool and gas is off
• Lift out the old grate and set the new grate in place—no special tools typically required
• Avoid harsh abrasives; clean with non-abrasive soap and water to preserve finish
• Inspect surrounding porcelain/enamel and burner caps for proper seating after installation

This #6-32 machine screw fastens panels, brackets, and small assemblies in appliances to restore secure, rattle-free operation. It's a common replacement for stripped or missing fasteners used on covers, consoles, and internal components. What it does

• Secures panels, trim, brackets, and small components to prevent movement and noise
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment of assemblies to avoid intermittent electrical contact
• Restores the intended fastening strength for safe, reliable operation

• Disconnect power before accessing internal components
• Use the correct driver to avoid stripping the head
• Thread gently and avoid over-tightening to prevent damage to mating parts
• Keep small parts away from children and pets

This silicon controlled rectifier (SCR) is an electronic switching component used on appliance control boards to regulate power to heating elements or motors, restoring proper control and operation when the SCR fails. What it does:

• Acts as a power-control switch on control boards to deliver variable current to heaters or motors
• Helps regulate on/off cycles and output under control-board commands
• Failure may cause no heat, intermittent heating, or components not running as expected
• Replacing a faulty SCR can restore consistent power control and appliance function

• Disconnect all power before servicing; risk of electric shock or damage
• Static-sensitive component—use proper ESD precautions when handling
• Replacement typically requires desoldering/soldering on the control board or replacement of the control module

This venturi directs and mixes propane (LP) gas with air for proper burner combustion on compatible gas ranges and cooktops. It helps restore consistent flame shape and burner performance when the venturi is damaged or clogged. What it does:

• Channels LP gas to the burner for correct air/gas mixing
• Helps maintain stable, even burner flames during operation
• Commonly replaced if the venturi is cracked, clogged, or warped
• Can resolve weak or uneven flames and ignition difficulties

• One venturi (15K LP) as shown

• Turn off gas supply and power before servicing; follow local codes
• Install only on compatible LP-configured appliances and use correct orifice sizes
• Inspect surrounding seals and connections; replace any damaged hardware

This harness module routes power and control signals between the appliance control system and internal components to restore reliable electrical connections and proper function. What it does:

• Connects control board circuits to motors, switches, sensors, or valves for coordinated operation
• Re-establishes intermittent or lost electrical paths that can cause components to stop responding
• Helps resolve symptoms like parts that won't run, intermittent operation, or related error codes
• Ensures connectorized wiring is organized for correct signal routing and secure contact

• Disconnect power to the appliance before accessing electrical components to avoid shock
• Handle connectors gently; match keyed plugs and fully seat each connector during installation
• Route harness away from heat sources and moving parts; secure with existing clips or ties
• If wiring, insulation, or connectors are damaged, replace the entire harness rather than splicing

This angle support is a small metal mounting bracket that stabilizes and secures components inside the appliance, helping keep shelves, panels, or assemblies aligned for reliable operation and safe use. What it does:

• Provides structural support for interior panels, shelves, or trim to prevent sagging or misalignment
• Holds assemblies in the correct position to reduce rattling and vibration during use
• Restores proper fit and clearance when a bent or broken bracket causes shifting
• Works with fasteners to anchor components where a right-angle connection is needed

• Inspect surrounding parts and fasteners; replace any damaged screws or clips as needed
• Use the correct size fastener and torque to avoid stripping or cracking adjacent parts
• Disconnect power and follow manufacturer safety guidelines before working near electrical components

This retainer is a small mounting clip that secures compatible appliance components in place to prevent movement and wear. It restores proper alignment so related parts stay seated and operate quietly and safely. What it does:

• Holds a specific component or harness firmly to the appliance frame or assembly
• Prevents rubbing, vibration noise, or parts shifting during operation
• Helps maintain correct part alignment for reliable function
• Common symptom: loose, rattling, or misaligned components where the retainer is missing or damaged

• One retainer

• Disconnect power and any fuel sources before starting work
• Inspect surrounding parts for damage before installing the retainer
• Typically installs with basic hand tools; avoid over-tightening nearby fasteners