Ge Dpse810gg0wt Parts

This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.

Fix a dryer that won't start, has a dead console, or runs erratic cycles by replacing the electronic control board. DIY-friendly repair.

Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.

Fix a dryer that won't heat with this outlet backup thermostat. Mounts on exhaust duct for over-temperature protection. DIY repair in under 1 hour.

Fix electrical grounding issues with this dryer ground strap assembly. Restores proper chassis grounding to reduce shock risk. Simple repair for worn connections.

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.

Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.

Converting your dryer from LP propane to natural gas? This conversion kit includes the orifice and components needed for a quick, straightforward swap.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

This adjustable gray foot supports and levels your dryer, allowing you to compensate for uneven floors. It screws into the dryer's base and can be raised or lowered to ensure the appliance sits level and stable. Replace this part if your dryer rocks, vibrates excessively, or appears tilted.

Fix a dryer that won't heat or cycles but doesn't ignite with this gas burner assembly. Restores consistent flame when the original is corroded or clogged.

Rear bracket and leveling screw assembly.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Replaces damaged outer and inner door panels to restore appearance and maintain proper door alignment. Replace if panels are cracked, warped, or dented. Verify fit with your model number.