Gfc170f Parts

This compressor grommet is a rubber mounting isolator that cushions and secures the compressor to the appliance chassis, helping reduce vibration and noise while preventing metal-to-metal contact and premature wear. What it does:

• Cushions compressor movement to reduce vibration transmitted to the cabinet
• Dampens noise and rattling caused by compressor operation
• Prevents direct metal-to-metal contact that can wear mounting points
• Helps keep the compressor positioned and secured under load

• Disconnect power to the appliance before accessing the compressor or base pan
• Replace grommets while supporting the compressor to avoid strain on lines and connections
• Inspect remaining mounting grommets; replace all worn isolators for best performance

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material

This door gasket is a replacement refrigerator door seal that helps maintain an airtight closure to keep cold air in and reduce temperature fluctuations. Restores proper sealing to help the fridge run efficiently and protect food. What it does:

• Seals the refrigerator door to prevent warm air from entering and cold air from escaping
• Helps reduce frost buildup and uneven cooling caused by a failing seal
• Can lower strain on the compressor by improving temperature stability
• Addresses symptoms such as visible gaps, drafts, or moisture buildup around the door

• Disconnect power to the appliance before starting any work
• Clean and dry the door frame surface before installing the new gasket for a tight seal
• Remove the old gasket carefully; use hand tools and avoid sharp implements that could damage the cabinet
• Follow the appliance manufacturer's installation instructions for proper fit and tab alignment

This small mounting clip secures interior or cabinet components to keep panels and trim stable, helping reduce noise and maintain proper alignment. It's a simple replacement that restores a snug fit where the original clip has broken or worn. What it does:

• Holds panels, trim, or small components in place to prevent gaps or rattling
• Restores proper alignment of clipped parts after damage or wear
• Maintains a secure attachment point for adjacent parts during normal use
• Helps prevent moisture or debris from entering behind secured panels

• Disconnect power or unplug the appliance before accessing internal components
• Handle the clip and surrounding trim carefully to avoid cracking adjacent plastic
• Use basic hand tools as needed; do not force clips into place—align before snapping
• Replace any damaged mounting features for a secure fit

This drain tube insulation cushions and thermally protects the refrigerator's defrost drain tube to help prevent condensation and ice buildup. It keeps the drain line insulated so water flows freely to the drip pan and reduces drip/ice-related issues. What it does:

• Wraps around the defrost drain tube to limit heat transfer and condensation.
• Helps prevent drain freeze-ups that can cause water pooling or slow drainage.
• Reduces the chance of water dripping inside the cabinet or onto the floor.
• Supports reliable defrost water routing to the drain pan.

• Always unplug the appliance or disconnect power before servicing.
• Access may require removing the back or inside panel; keep track of fasteners.
• Slide the insulation over the drain tube so it fully covers the exposed section; ensure it sits flat without kinks.
• If corrosion or heavy buildup is present, clean the drain tube before installing new insulation.

This inner lid panel replaces the damaged or worn interior surface of the washer's upper lid, restoring a finished appearance and helping the lid secure properly. Designed to match the OEM lid assembly fit. What it does

• Provides the finished inner surface of the washer lid so the lid closes and seals as intended
• Replaces cracked, broken, or warped inner lid material that can catch clothes or interfere with lid operation
• Stops interior rattles or movement caused by a loose or deteriorated inner panel
• Helps maintain proper alignment between the lid and latch for reliable closing

• One inner lid panel (upper washer lid panel) as pictured

• Disconnect power to the appliance before beginning any repair
• Remove screws or retaining clips from the outer lid to separate the inner panel; keep fasteners for reinstallation
• Handle edges carefully to avoid damaging trim or the new panel; common hand tools required

A small replacement mounting clip that secures interior trim and panels to restore proper fit and reduce rattling. Use when a broken or missing clip leaves gaps or lets panels or trim sit loose on the appliance. What it does:

• Secures trim, access panels or small plastic covers to the appliance frame
• Restores proper alignment and helps eliminate panel vibration or rattling
• Replaces cracked, worn or missing clips that allow gaps or loose parts
• Works as a simple fastener where the original clip has failed

• Always disconnect power to the appliance before beginning any repair
• Clip typically installs with a push-fit or snap-in motion; a flat tool may help remove the old clip
• Handle surrounding trim gently to avoid cracking brittle plastic
• Verify correct clip orientation before snapping into place