Gfds350eloww Parts

This control panel assembly replaces the white front console on your dryer. It restores a solid mounting surface for the timer, switches, or display so you can select cycles and settings with proper alignment and smooth operation. What it does

• Provides the front console housing for the dryer's user controls
• Keeps buttons/knobs and indicators aligned and protected
• Restores appearance after cracks, discoloration, or broken tabs
• Helpful when controls feel loose, are hard to press, or the console is rattling

• 1 white control panel assembly

• Disconnect power; if gas, shut off the gas supply before servicing
• Remove control knobs and any end caps; take out mounting screws/clips and lift off the old panel
• Transfer any brackets, light pipes, clips, and harness retainers from the old panel to the new as needed
• Reinstall and tighten fasteners; refit knobs and verify smooth control operation before restoring power

Protective cover that shields the rear power connection terminals on your dryer. Replace if cracked, broken, or missing to prevent lint buildup and accidental contact with electrical connections.

Dryer door won't latch or stay closed? This strike plate mounts at the door opening to catch the latch securely. Easy DIY repair for reliable closing.

Dryer door gasket seal creates an air barrier around the door perimeter. Replace if worn, torn, or causing heat loss. Confirm fit with your model number.

This genuine replacement part is a user interface board for dryers. The user interface board is the circuit board that responds to the buttons located on the control panel allowing the user to adjust the dryer settings. If the dryer is no longer responding when buttons are being pressed then it might be time to replace the user interface board. Luckily this is a relatively easy repair.To replace the interface board begin by turning off the power to the dryer. Once the power has been shut off move the dryer away from the wall to gain access to the upper back panel. Remove the panel and locate the interface board. Snap it out of its brackets and remove the wire harness attached to the board. Reinsert the wire connector to the new interface and snap the new board assembly back to its original place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand Dryers.

This adjustable gray foot supports and levels your dryer, allowing you to compensate for uneven floors. It screws into the dryer's base and can be raised or lowered to ensure the appliance sits level and stable. Replace this part if your dryer rocks, vibrates excessively, or appears tilted.

Rear bracket and leveling screw assembly.

This dryer inlet thermostat monitors the temperature of incoming air and cycles the heater to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent heat, help prevent overheating, and improve overall drying performance.

• Senses inlet air temperature and opens/closes electrical contacts to control the heat source
• Helps regulate drying temperature and protect against overheating
• Failure may present as long dry times, no or intermittent heat, overheating/shutting off, or erratic temperature swings
• Typically mounted on the air intake/duct or blower housing, depending on model

• Disconnect power before service; if gas, also shut off the gas supply
• Access the thermostat at the front duct or blower housing; note wire positions and transfer one at a time
• Mount flush against the metal surface with existing hardware to ensure proper sensing
• After installation, clear lint from ducting and vents to ensure proper airflow

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Black plug button that covers unused control openings on your dryer control panel. Replace when cracked, broken, missing, or worn to restore a finished look.

Protection bracket for dryers. Mounts internally to shield components from damage. Replace if bent, broken, or missing to restore proper protection.

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

Size: 8-32 t. Includes 12 screws.

Includes 12 screws. Size: 8-18 ab.

Secures the door guide strip to your dryer frame, keeping the door aligned. Replace this nut if it's missing, stripped, or worn to restore proper fit.