Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Seals duct connections to maintain proper airflow and contain heat and lint. Replace if you notice reduced drying performance or air leaks. Confirm fit.
Usually ships within 4 - 14 days
Dryer door gasket seal creates an air barrier around the door perimeter. Replace if worn, torn, or causing heat loss. Confirm fit with your model number.
This genuine replacement part is a user interface board for dryers. The user interface board is the circuit board that responds to the buttons located on the control panel allowing the user to adjust the dryer settings. If the dryer is no longer responding when buttons are being pressed then it might be time to replace the user interface board. Luckily this is a relatively easy repair.To replace the interface board begin by turning off the power to the dryer. Once the power has been shut off move the dryer away from the wall to gain access to the upper back panel. Remove the panel and locate the interface board. Snap it out of its brackets and remove the wire harness attached to the board. Reinsert the wire connector to the new interface and snap the new board assembly back to its original place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand Dryers.
Replacing the board took about two minutes from start to finish after removing the select knob. Extremely easy but costly. Read more
Fix a dryer that won't turn on or power up. This main power control board restores electrical functions. Moderate DIY repair for experienced users.
I have a background in electronics repair. I checked the power board and found out there was no 12 volts DC coming out of the unit. The 12 volts powers the various relays. It also goes to the power switch and other switches on the front user interface panel. Using my multi meter there was 110 volts coming in and nothing going out so I decided to replace the power pcb. It arrived within 3 days. I turned off the power and installed it and now my dryer works! My wife is so happy! No more trips to... Read more
Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
Replaces the front console housing the keypad and display on your dryer. Needed when buttons are loose, missing, cracked, or panel is damaged or worn.
Replace stripped, missing, or damaged #8-32 x 1/2 machine screws that secure dryer panels, brackets, and internal components. Restores proper fit.
Replaces the rear mounting bracket that secures a leveling leg to your dryer frame. Needed when the original bracket is cracked, broken, or missing.
Steam generator assembly for dryers with steam-refresh cycles. Installs inside cabinet to heat and release steam. Replace if cracked, leaking, or damaged.
Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.
This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does
Shoe rack accessory that sits inside your dryer drum for air-drying shoes or delicate items. Replace if cracked, broken, or missing from your unit.
They could not find part and sent it on to the research dept and I really did not expect to hear from them again as most employees wont do what they say they will today. They actually sent me an email with the part No and I ordered it. Only one in stock for the Model I needed and tickled my mom as she never knew of a dryer shelf before. Read more
Meters gas flow to the dryer burner. Replace if damaged, clogged, or when converting between natural gas and LP. Installs at the burner assembly.
The installation of the correct orifice fixed it. While doing that repair, I installed a new drive belt. My dryer is up and running again. The rapid shipment of the parts was most appreciated.. Thank you. Read more
Replacement mounting screw for your dryer. Secures panels, components, and internal parts. Order a new screw if the original is stripped, missing, or damaged.
Replace your dryer's display window lens if it's cracked, scratched, or missing. This clear protective cover installs over the control panel display.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.