Gfe28hgh Parts

The Cover Latch is an OEM part for GE refrigerators. This part serves as a cover for the latch handle, ensuring a seamless look for the appliance while protecting the latch handle from damage and wear.

Causes of a bad Cover Latch can include wear and tear over time, impact or mishandling that leads to cracks or breaks, or general deterioration due to prolonged use.  

Symptoms of a bad Cover Latch include:

• Visible cracks or breaks
• The latch handle not being properly covered
• Difficulty in operating the latch handle
• Loose or missing cover latch

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The RFID Water Filter Board is an OEM part for GE refrigerators. It is an electronic component located inside the filter housing that reads the RFID chip in Genuine GE water filters. The board monitors filter life and provides notification when it's time for a replacement. 

Symptoms of a bad RFID water filter board include:

• Inability to detect when a new filter is installed  
• Error codes or filter life indicators not functioning properly
• Water dispenser not working or dispensing unfiltered water

Causes may include damage from moisture or leaks over time, failure of electronic components, or normal wear and tear.

This replacement board is also compatible with Hotpoint, RCA, and some Kenmore models.

This refrigerator drain tube and valve assembly channels defrost water to the drain pan, while the valve helps block warm air from entering the drain. Replace a cracked or clogged assembly to address leaks and recurring ice buildup. What it does:

• Routes defrost water from the evaporator to the drain pan beneath the unit
• Integrated valve helps prevent warm air backflow that can lead to frost and drain clogs
• A damaged or obstructed tube/valve may cause water inside the compartments or on the floor
• Visual cracks, deformation, or blockage indicate the assembly should be replaced

• One drain tube and valve assembly

• Disconnect power and wear cut-resistant gloves before servicing
• Pull the refrigerator forward and remove the rear lower access panel
• Locate the drain outlet above the drain pan; remove the old tube/valve and clear any debris from the drain
• Seat the new assembly fully and ensure proper routing into the drain pan before restoring power

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Refrigerator Evaporator with Heater is an OEM part for GE refrigerators. This component cools the air within the freezer and fresh food compartments through vaporization and circulation. It also contains an internal heater to prevent condensation and frost formation.

Causes of a bad evaporator can include normal wear over time, damage from leaks, or issues with the heater component. 

Symptoms of a bad evaporator include:

• Inadequate or inconsistent cooling within compartments  
• Frost or condensation buildup that requires frequent defrosting
• High energy usage but inability to maintain proper temperatures
• Foreign or musty odors emanating from within the refrigerator

Replace this evaporator to restore optimal cooling performance, efficiency, and freshness preservation in your refrigerator. This GE OEM part is also compatible with later Hotpoint, RCA, and select Kenmore refrigerator models.
 

The Icemaker Fill Cup is an OEM replacement part for GE refrigerators responsible for directing the water flow into the icemaker, allowing for the creation of ice cubes. It securely attaches to the icemaker, preventing any leaks or spills that could disrupt the ice production.  

A bad fill cup can occur due to several factors. Common causes include cracks, damage, or wear and tear over time. If you notice symptoms such as leaks around the icemaker, improper ice production, or water overflow, it may indicate a need to replace the fill cup.

Symptoms of a bad fill cup include:

• Leaks around the icemaker area
• Insufficient or inconsistent ice production
• Water overflow or spills

Restore your refrigerator's ice-making capabilities by replacing the faulty fill cup with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Striker Light Switch is an OEM component specifically designed for GE refrigerators. Located on the refrigerator door, it controls interior lighting functions.

Causes of a bad switch can include wear from opening the door frequently or water damage over time.

Symptoms of a failed switch include: 

• Lights not turning on when the door is opened  
• Lights remain illuminated all the time even when closed
• Flickering or unresponsive lighting behavior

This switch utilizes a striker plate activation mechanism that triggers interior lights based on door position - open or closed. A replacement ensures lighting convenience and energy efficiency. 

This genuine OEM GE part restores dependable on/off lighting control through the normal door operation process. Compatible with additional brands including Hotpoint, RCA, or Kenmore models.

The Icemaker Fill Tube Heater is an OEM component specifically designed for GE refrigerators. Located near the icemaker assembly, this heating element plays a crucial supporting role.

Symptoms of a bad fill tube heater include:

• Irregular or inconsistent ice production amounts  
• Cracked, cloudy or malformed ice cubes being generated
• The icemaker failing to operate or stop working altogether
• Water or moisture around the refrigerator icemaker area 

Causes can include wear over time from powering on during each ice-making cycle. Mineral deposits may also form and insulate the heating surface, reducing effectiveness.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

Replace a worn or leaky seal with this fresh food door gasket. It creates a tight, uniform seal around the refrigerator compartment door to keep cold air in, reduce condensation, and help maintain consistent temperatures.

• Forms an air-tight perimeter seal between the fresh food door and cabinet
• Helps stabilize refrigerator temps and reduce warm air infiltration
• Can address issues like gaps in the seal, door not closing flush, temperature swings, or moisture/condensation around the door edge
• Restores proper sealing after the original gasket becomes torn, warped, or compressed

• Disconnect power before servicing; use caution around sharp door liner edges
• Soften the new gasket in warm water or with a hair dryer on low to relax folds—do not overheat
• Seat corners first, then work along the sides into the door channel; on some models, loosening retainer screws may be required
• Check the seal with a paper-bill test and adjust door alignment if needed; allow time for the gasket to conform

The Door Handle is an OEM component specifically designed for GE refrigerators. It plays an essential role in allowing users to easily grasp and open the refrigerator door. 

The door handle is responsible for providing a sturdy grip that facilitates access to the refrigerator's contents. It is engineered to withstand regular opening and closing without damage for years of dependable use. 

Causes of a bad door handle can include wear and tear from frequent use, swelling or cracking due to weather conditions, damage from excessive force, or broken/missing components that compromise the handle's grip and functionality. 

Symptoms of a bad door handle include:

• Difficulty opening the refrigerator door 
• The door handle coming loose or falling off
• Breakage that results in an unusable or unstable grip
• Cracks, swelling, or other visible defects

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 
 

This spring feeler arm is the replacement sensing arm used with the refrigerator ice maker assembly to detect ice level and help actuate the ice-making mechanism. Restores proper ice sensing and helps prevent overfill or stoppage. What it does:

• Acts as the ice maker's feeler/bail arm to detect when the ice bin is full or empty.
• Triggers the ice maker to stop or continue cycles based on ice level.
• Helps prevent overfilling and reduces ice production problems caused by a bent or broken arm.
• Can stop erratic ice maker behavior when the original arm is damaged or worn.

• Disconnect power to the refrigerator before beginning any repair.
• Handle the arm carefully and inspect the ice maker mounting points for damage before installation.
• Reuse factory hardware if undamaged; replace any stripped or missing fasteners.

This bar reinforcement is a replacement support brace that restores strength and alignment to the appliance trim or door assembly. It helps secure panels and prevents sagging or flexing for reliable everyday use. What it does:

• Provides structural support for the door or trim assembly to reduce flex and maintain alignment
• Restores a loose or sagging panel to proper position
• Helps keep connected components stable during normal operation
• Designed to fit into the original mounting points and distribute load where the factory part did

• Follow the appliance manufacturer's service manual for disassembly and reassembly steps
• Use appropriate hand tools; avoid overtightening fasteners to prevent damage
• Disconnect power (or gas, if applicable) and remove food/contents from working area before starting

The Refrigerator Slide Lower Freezer is an OEM replacement part for GE refrigerators. It is a sliding component designed to facilitate smooth and effortless access to the lower freezer compartment. This OEM part ensures that the lower freezer drawer can glide in and out seamlessly, allowing for convenient storage and retrieval of frozen items.

Symptoms of a bad Refrigerator Slide Lower Freezer include:

• Difficulty opening or closing the lower freezer drawer
• Freezer drawer catching or sticking during operation
• Noisy or grinding sounds when sliding the drawer
• Drawer not staying in position when opened or closed

Causes of a bad lower freezer slide can include wear and tear from repeated use, damage from mishandling or overloading, or issues with the slide mechanism itself. Over time, the slides may become worn, misaligned, or obstructed, leading to operational problems.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

This evaporator block seal is a refrigerator freezer gasket that helps seal the evaporator assembly to limit air and moisture migration, reducing frost buildup and helping the cooling system run efficiently. What it does:

• Seals the evaporator block area to prevent moist air from reaching cold surfaces
• Helps reduce frost and ice accumulation on the evaporator and evaporator cover
• Supports consistent cooling by maintaining the intended airflow path
• Can reduce defrost frequency when the original seal is damaged or worn

• 1 evaporator block seal

• Disconnect power to the appliance before starting any repair
• Replacement typically requires removing the evaporator cover or assembly; handle evaporator fins and components carefully
• Inspect surrounding foam, clips, or adhesive; replace or resecure as needed to ensure a proper seal
• After installation, restore power and verify proper cooling and defrost operation