Gi0saxvy02 Parts

Fix water splashing or misdirected flow during fill cycles with this fill cup insert. Channels water correctly to prevent leaks. Simple DIY repair.

Replace cracked or broken pantry drawer glass cover in your refrigerator. Restores shelf surface above full-width deli drawer. Verify fit by model number.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Mounting bracket that secures panels, doors, or internal components in your refrigerator. Replacement needed when original is cracked, broken, or missing.

Freezer not cold enough or stuck in defrost mode? This defrost thermostat regulates defrost cycles to prevent ice buildup and maintain proper cooling.

This circular component guides and directs water or ice from the dispenser to the user's container. Located in the refrigerator door dispenser area, replacement is needed when dispensing becomes inaccurate, messy, or completely blocked.

Support brace for 36-inch crisper drawer assembly. Restores secure mounting and alignment. Replace if cracked, broken, or causing drawer instability.

Plastic mounting yoke that secures and aligns the ice chute assembly to the door. Replace if cracked, broken, or causing misalignment issues.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

Replacement mounting screw for refrigerators. Secures panels, trim pieces, and small assemblies. Needed when original screw is missing or damaged.

Ice dispenser drawer cracked or missing? This refrigerator dispenser drawer bucket collects and holds ice securely, preventing spills and messes.

Replaces cracked, broken, or worn refrigerator door handle. Installs on the door panel to restore secure grip and smooth opening on compatible units.

This cover hinge assembly secures and guides the appliance lid or top panel so it opens and closes smoothly. Replacing a worn hinge restores proper lid alignment and helps eliminate sticking, sagging, or uneven closure. What it does:

• Provides a pivot point for the lid/top cover, holding it in the correct position during use
• Restores smooth opening and closing when original hinge is bent, worn, or broken
• Helps eliminate lid sag, misalignment, or rubbing against the cabinet
• Works with the appliance's existing bracketry and fasteners to maintain fit and function

• One cover hinge assembly

• Basic hand tools required; keep fasteners organized for reassembly
• Disconnect power and follow appliance-specific safety guidelines before beginning repair
• Inspect mating surfaces and replace any damaged screws or brackets for a secure fit

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

Ice dispenser not working or making grinding noises? This auger motor drives the spiral shaft that moves ice from the bin to the dispenser chute.

Secures internal components to the refrigerator chassis. Replace this mounting bracket if cracked, bent, or broken to restore stable support alignment.