Gie22jsnbrr Parts

This replacement clamp secures lines or components inside the refrigerator, keeping them properly routed and stable. Replacing a broken or missing clamp helps reduce vibration and prevents rubbing damage or leaks from loose tubing. What it does:

• Holds tubing or wiring harnesses securely in place inside the refrigerator
• Maintains correct routing and clearance to prevent chafing and wear
• Helps reduce vibration and rattling noises from unsecured lines
• Can help prevent drips or leaks when used to retain water tubing

• 1 clamp

• Unplug the refrigerator and, if working with water lines, shut off the water supply
• Note the original clamp orientation and routing; take a photo before removal
• Install the new clamp in the same location, securing lines without pinching or over-stressing them
• Restore power (and water if applicable) and check that lines are secure; inspect for leaks if used on water tubing

This plastic water tube routes water inside your refrigerator to the dispenser and/or ice maker. Replacing a cracked, brittle, or leaking tube restores proper water flow and helps prevent leaks and water damage.

• Directs water between components such as the inlet valve, reservoir, door, dispenser, or ice maker (varies by model)
• Maintains a sealed, food-grade path to prevent leaks and air intrusion
• Damage can lead to puddles behind/under the fridge or inside the fresh food compartment
• Common symptoms: slow/no dispenser flow, ice maker not filling or making small cubes, visible cracks/kinks

• Unplug the refrigerator and shut off the household water supply; relieve line pressure at the dispenser
• Note tube routing and connection points before removal; avoid sharp bends and kinks during install
• Cut tube ends square and fully seat into compression or push-in fittings
• Restore water, check all joints for leaks, and run water to purge air from the system

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replace it when the original is torn, warped, or leaking to restore proper temperature and defrost performance.

• Creates a continuous seal around the freezer door to prevent air leaks
• Helps maintain set temperatures and reduces frost/condensation buildup
• Replaces a gasket that is cracked, torn, deformed, or no longer sealing
• Common symptoms: frost or moisture along the door edge, door not closing fully, warm spots near the gasket

• Disconnect power before servicing
• Let the new gasket warm up (room temperature or brief warm-water soak) to increase flexibility
• Seat the gasket fully in the retainer/channel; use low heat (hair dryer) to relax waves—do not overheat
• Check the seal with a paper/dollar-bill test around the perimeter and adjust alignment if needed

This factory screw secures brackets, panels, and internal components so assemblies stay tight and aligned. Replace a missing or damaged fastener to eliminate rattles, looseness, and misaligned parts. What it does:

• Fastens components, panels, hinges, or brackets to the appliance frame
• Helps maintain proper alignment and a solid, rattle-free fit
• Replaces stripped, rusted, or missing hardware
• Can address vibration noises and loose assemblies

• Includes 1 screw

• Unplug the appliance and shut off water before servicing
• Wear gloves; sheet-metal edges can be sharp
• Start threads by hand to avoid cross-threading; use the appropriate driver
• Tighten snugly—do not overtighten to prevent stripping

This center hinge supports and pivots the refrigerator door at the middle of the cabinet. Replacing a bent or worn hinge restores smooth door movement and a reliable seal to help maintain proper temperatures.

• Supports door weight and provides the center pivot for opening and closing
• Helps maintain door alignment for even gasket contact
• Wear or damage can cause sagging, rubbing, squeaks, or doors that won't close/seal
• Visible bending, looseness, or a damaged hinge bracket/pin indicates replacement is needed

• Disconnect power and remove items from the door to reduce weight
• Support the door and have a second person assist; note the order of any spacers/washers
• Remove mounting screws, replace the hinge, and reinstall while keeping the door square
• Verify the door swings freely and the gasket seals evenly; adjust alignment as needed

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This leveling leg supports and stabilizes the refrigerator cabinet. Adjusting it keeps the unit level so doors align and seal correctly, helping reduce vibration and noise for smoother, more reliable performance.

• Threads into the base to support and level the appliance
• Allows height adjustment for proper door alignment and gasket contact
• Helps reduce rocking, vibration, and rattling noises
• Resolve issues like doors not closing fully, uneven gaps, or a wobbly cabinet

• Disconnect power and move the appliance carefully to access the leg
• Use a helper and protect flooring; tip the unit slightly and support it securely
• Unthread the old leg; hand-thread the new leg, then adjust as needed with a wrench
• Level front-to-back and side-to-side; avoid cross-threading or overtightening

This reversible door plug is a small trim cap that fills the unused holes on a refrigerator door after changing the door swing. It restores a clean, finished look and helps keep dust and moisture out.

• Covers unused hinge/handle screw holes created during a door reversal
• Press-fit cap designed to match lighter gray door trim
• Helps maintain appearance and reduce entry of dirt and moisture
• Replace if missing, cracked, discolored, or won't stay seated

• Disconnect power if removing or repositioning the door/hinges
• Use your model's parts diagram to confirm the plug location and color
• Align with the hole and press in by hand until flush with the surface
• Do not force; verify correct part if the plug will not seat properly

This replacement gasket seals the refrigerator's fresh food compartment in Dorian Gray. It closes gaps around the door to keep cold air in and humid air out, helping stabilize temperatures and reduce condensation for reliable cooling.

• Seals the perimeter of the fresh food door to prevent warm air leaks
• Helps maintain proper temperature and humidity in the refrigerator section
• Reduces condensation or "sweating" around the door area
• Common signs it's worn: tears, cracks, warping/shrinkage, visible gaps, or the door not sealing fully

• Unplug the refrigerator and unload the door bins
• Pull the old gasket from the retainer; on some models, slightly loosen (do not remove) liner screws to release the seal
• Warm the new gasket in hot water or with low, safe heat to relax it; seat corners first, then press the gasket fully into the retainer
• Close the door to check for even contact all around; adjust as needed and allow up to 24 hours for the gasket to conform

The Fresh Food Glass Shelf is an OEM part for GE refrigerators. It provides an adjustable glass shelf area inside the fresh food compartment for organizing food items in an open layout. The glass measures approximately 22 inches.

Causes of a bad shelf can include chips or cracks developing from repeated impact or stress from heavy loads over time. Improper cleaning leading to scratches or dulling of the glass surface is also possible.

Symptoms of a bad Fresh Food Glass Shelf  include: 

• Visible cracks or chips in the glass that compromise structural integrity
• Dull, scratched, or filmy glass that inhibits the visibility of food contents  
• Failure to slide smoothly or stay locked into position on shelf supports

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Handle Mount is an OEM component specifically designed for GE French door refrigerators. It serves as the attachment point for refrigerator door handles.

The handle mount connects the handle assembly securely to the refrigerator door itself. Its sturdy construction manages stress from frequent usage while allowing for smooth operation.

Symptoms of a bad handle mount include:

• Loose, unstable, or detached door handles
• Handles difficult-to-operate or open doors with  
• Visible bending, cracks, or damage to the mount
• Reduced grip strength or door control

Causes can involve normal wear over extended periods, imprecise impacts, or repeated stress from heavy handling exceeding the mount’s limits. 

Replace with this genuine GE OEM part to restore a tight, lasting connection between handles and doors. Compatible also with Hotpoint, RCA, and Kenmore French door refrigerator models.
 

This small hardware clamp is used on select refrigerators to secure tubing or wiring to the cabinet or frame. Replaces a missing or damaged clamp to keep lines stable, reduce vibration, and help prevent rubbing or leaks.

• Secures small water tubing or electrical harnesses along the cabinet/frame
• Helps prevent vibration, rattling, and abrasion of lines
• Maintains correct routing to keep lines clear of moving or hot components
• Common clues: loose or noisy lines, chafing marks, or moisture near tubing connections

• Unplug the appliance and shut off the water supply before servicing
• Note the original location and routing; take a photo for reference
• Reuse the existing mounting screw/fastener if required; tighten only enough to hold without crushing tubing
• Restore power and water, then run and inspect for vibration and leaks

This hex-head screw secures dishwasher panels, brackets, and internal hardware so parts stay tight and rattle-free. Replace missing or stripped fasteners to restore a secure fit and reliable operation.

• Fastens panels, brackets, and other dishwasher components to the tub or frame
• Replaces a missing, stripped, or corroded screw that no longer holds securely
• Helps eliminate vibration and rattling caused by loose hardware
• Maintains proper alignment and secure mounting of parts during operation

• Disconnect power and shut off water supply before servicing
• Keep track of fastener locations and orientation for correct reassembly
• Start threads by hand; use an appropriate nut driver or socket to tighten
• Tighten snugly—do not overtighten, especially when threading into plastic

This gasket supply foam is a replacement foam seal strip used to restore a refrigerator door or cabinet seal cushion for a tighter fit and improved temperature control. It helps reduce drafts and keeps fresh food fresher. What it does:

• Replaces worn or compressed foam that can allow air leaks around the door or compartment
• Restores the gasket's shape and cushioning to improve door sealing performance
• Helps reduce humidity build-up and cycling from frequent compressor starts
• Addresses symptoms such as visible gaps, cold loss, frost buildup, or higher energy use

• Remove old foam and any adhesive residue before installing the new strip
• Use appropriate gasket adhesive and follow manufacturer instructions if required
• Work with the appliance unplugged or power turned off; keep fingers clear of pinch points

A top door hinge and pin assembly that supports the refrigerator/freezer door and lets it pivot smoothly for reliable opening and closing. Replaces a worn or damaged top hinge to restore proper door alignment and seal. What it does:

• Provides a durable pivot point so the door swings open and closed smoothly
• Restores proper door alignment to help the gasket seat and maintain cooling
• Stops squeaks, sticking, or uneven door movement caused by a worn hinge
• Supports the door weight to prevent sagging or dragging

• One hinge top and pin assembly

• Disconnect power to the appliance before starting work and keep stored food safe
• Remove items from the door and support the door while replacing the hinge (two people may be needed)
• Retain any mounting screws; replace only parts explicitly shown in OEM documentation