Gld690tww-00 Parts

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This inlet cover is a replacement trim piece that protects and finishes the washer's water inlet area, restoring a clean appearance and guarding internal inlet components from dirt and accidental contact. What it does

• Covers the water inlet opening and surrounding inlet assembly for a finished look
• Helps shield inlet valves and connections from debris and incidental contact
• Maintains proper alignment and fit of the inlet area trim
• Restores cosmetic appearance after damage or loss of the original cover

• One inlet cover

• Disconnect power and shut off water supply before starting any work
• Access may require removal of the washer top or control console depending on model
• Typically secures with clips or a few screws; have a screwdriver set on hand
• Replace if cracked or broken—do not attempt to use a damaged cover

A small rack clip that holds stemmed glasses upright during dishwasher cycles, reducing tipping and breakage. Restores proper support for wine glasses and other stemware so they wash safely and stay secure. What it does:

• Secures the stem of wine glasses and goblets to keep them stable during wash and rinse cycles.
• Prevents tipping, chipping, and breakage caused by glasses shifting in the rack.
• Replaces cracked, broken or missing stemware clips that allow dishes to move or clink.
• Helps reduce noise from glassware hitting the rack when the clip is damaged or absent.

• Remove dishes and ensure the dishwasher is off before replacing the clip.
• Seats into the dishwasher rack slot—press into place until fully seated; no special tools usually required.
• Refer to your appliance manual for model-specific instructions and safety guidance.

This mounting bracket secures the dishwasher tub or inner components to the cabinet or frame, helping keep the appliance stable during cycles and preventing movement or misalignment. What it does:

• Provides a secure attachment point between the dishwasher and the cabinet or chassis
• Helps reduce rattling, shifting, and vibration during operation
• Keeps inner panels and assemblies aligned for proper door operation
• Supports correct positioning that can prevent wear on adjacent parts

• One dishwasher mounting bracket

• Intended for users comfortable with appliance repair; disconnect power and shut off water before starting
• Typical installation uses screws or clips—retain original fasteners unless replacement fasteners are specified
• Inspect surrounding mounting points and hardware; replace any damaged screws or tabs for a reliable fit

This upper spray arm assembly delivers a rotating spray pattern to distribute water across the upper rack, restoring proper wash coverage and improving cleaning performance for dishes and glassware. What it does:

• Replaces the upper spray arm to restore rotating water spray across the top rack
• Helps resolve poor cleaning or missed spots on upper-rack items
• Restores proper water distribution when spray arm is cracked, clogged, or not spinning
• Works with the dishwasher's spray system to reach hard-to-clean areas

• One upper spray arm assembly

• Turn off power and water supply before starting any repair
• Remove the upper rack to access the spray arm; follow OEM instructions for removal/replacement
• Inspect and clear any debris from the spray holes and mounting area before re-installing

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This air diverter assembly routes and redirects airflow inside the appliance to help maintain proper venting and circulation. Replaces a worn or broken diverter to help restore normal airflow and reduce venting issues. What it does:

• Directs airflow between ducts and chambers to maintain intended ventilation paths
• Helps prevent air from bypassing heating elements or sensors
• Can reduce symptoms like uneven drying, long cycles, or reduced airflow
• Stops rattling or unusual air-noise caused by a broken or loose diverter

• One air diverter assembly

• Disconnect power before beginning any repairs
• Access may require removing the appliance back panel or cabinet; keep track of fasteners
• Inspect mating surfaces and seals; replace damaged seals or gaskets for best performance

This shelf cup is a small replacement cup that secures a refrigerator door shelf in place, restoring shelf stability and preventing items from slipping or the shelf from sagging. It's a direct-fit replacement designed to match the original mounting. What it does:

• Supports and anchors a door shelf or shelf bin to the refrigerator door
• Keeps the shelf level so stored items don't slide or tip
• Replaces cracked, broken, or worn shelf cups that allow shelf movement
• Restores proper alignment and secure seating of the shelf/bin

• Disconnect power only if you must move or tilt the appliance; otherwise remove items from the door and work with the fridge closed
• Remove the affected shelf/bin and detach the old cup
• Press the new shelf cup into place until it seats fully; re-install the shelf/bin and check for secure fit