Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Usually ships within 4 - 14 days
Ground
This silicon controlled rectifier (SCR) controls power flow to heating and motor circuits, restoring proper electronic regulation in appliances that use SCR-based control boards. Replaces a failed SCR to help return normal heat and motor control. What it does:
The video was quite helpful with step by step instructions. I ordered a belt and idler pulley before dismantling assuming they were the issues. Belt was easy and fit fine but I did not realize the idler pulley was secured with a special fastener, push on cap nut, that would be damaged if removed. So I left it in place. Original pulley seemed fine so I reassembled the dryer. Restarted and of course the noise remained. I ordered the push on fastener and also the drum bearing as a precaution. ... Read more
The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.
Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.
Symptoms of a bad Knob Clip include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I actually called a repair service in our area. The serviceman asked questions and detected that I didn't need a timer unit but thought it was just a knob that was required. He offered to come out but the expense would be considerable. I am SO relieved that it was indeed the knob, and the dryer was fixed. In this time in our lives, every penny counts. I must applaud the serviceman for his honesty and dedication to his trade. He directed me to this website, but also added if there were any... Read more
The repair was easy and completed within 30 minutes. I also replaced the drum bearing pads. Because of the worn parts, the drum actually cut thru the existing light socket wires, so I probably could have just spliced them together to fix, but . Since I already purchased a new light socket assembly I just replaced it with the new one. Everything is installed and works great. Read more
Fix a dryer that won't cycle wrinkle care properly with this wrinkle care on/off switch. Simple 5-minute installation for most DIYers. Restores function.
Ordered the proper parts and replaced them. Read more
Replaced new parts with the new one, swapping one wire at the time. Read more
Replaces a cracked, rusted, or disconnected exhaust duct that routes hot air from your dryer to the home vent. Restores proper airflow and venting.
Removed front of dryer and back access plate allowing me to see that the pipe just slipped over the blower. A small tab in the back cover was inserted inside the left side of the pipe and when I straightened the tab I could move the pipe to the right and then straight out. Replacement of the pipe was the reverse. The new pipe did not have a hole for the tab, so I bent the tab to its original position, and rested the pipe against the tab. The new pipe had a rear flange that kept it in place.... Read more
This motor plate is the stamped metal mounting plate that secures the motor assembly and keeps it aligned for smooth operation. It restores proper motor positioning and reduces vibration-caused noise or wear. What it does:
This audio alert component signals the end of drying cycles and is located inside the dryer's control assembly. Replace it if the end-of-cycle signal doesn't sound, buzzes continuously, or produces weak or distorted tones.
My dryer was making a very loud noise while running. At first, a repair person came out and replaced the front plastic bearings but it had little effect. It appears that our rear bearing drum kit was also worn out, so I replaced that, but it still didn't solve it. Starting to feel like the dad from "A Christmas Story" who is always doing battle with an appliance in the basement, I set out to figure out what was causing it. Through trial and error, I was able to determine that the motor was... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.