Glhs36ejwo Parts

The Evaporator Fan Motor is an OEM replacement part for Frigidaire refrigerators. Located inside the freezer, this motor is responsible for powering the evaporator fan, which circulates cold air throughout the refrigerator and freezer compartments. 

Causes of a bad evaporator fan motor can include bearing wear, electrical faults, or failure due to extended use over time. Without proper air circulation, cold spots can develop inside the fridge.

Symptoms of a bad evaporator fan motor include:

• Inconsistent or fluctuating interior temperatures  
• Formation of frost or ice buildup
• Cold air not reaching all shelves and compartments evenly
• Excessive noise originating from the fan/motor area

This OEM Frigidaire replacement motor restores critical airflow needed to maintain temperatures. It is also compatible with refrigerator models by Electrolux, Gibson, Kelvinator, and Kenmore. 

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This small clip secures the crisper cover's slide so it stays aligned and operates smoothly. Replacing a broken or missing clip restores proper slide action and helps keep your crisper cover assembly functioning as designed.

• Holds the crisper cover slide in place and aligned with its track
• Helps the slide move smoothly without popping off or binding
• Common symptoms: slide is loose or falls out, won't stay in place, cracked/missing clip
• Visual damage or loss can leave the crisper drawer cover slide inoperable

• Disconnect power and remove food items for safe access
• Remove the crisper drawer and lift out the crisper cover assembly
• Release the damaged clip and snap the new clip into the cover/slide as oriented
• Reassemble and verify the slide moves freely end to end

This door hinge bearing fits the refrigerator door hinge and provides a smooth, low-friction pivot point. Replacing a worn bearing restores smoother door movement and helps maintain proper alignment and a reliable gasket seal. What it does:

• Provides a low-friction surface between the hinge pin and door
• Helps keep the door aligned for consistent gasket contact
• Reduces squeaks, scraping, or binding during opening and closing
• Helps with symptoms like door sagging, not closing fully, or uneven sealing

• 1 hinge bearing

• Disconnect power and remove items from the door before servicing
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Replace the bearing in the same orientation; reassemble hardware securely
• Reinstall the door and ensure smooth swing and full gasket contact around the perimeter

Used on fresh food and freezer doors.

This upper door hinge bearing serves as the low-friction bushing on the top hinge pin so the refrigerator door pivots smoothly. Replacing a worn bearing can stop squeaks and help restore level, easy-opening door operation.

• Provides a low-friction sleeve for the upper hinge pin to reduce wear
• Helps maintain door alignment with the cabinet for a consistent seal
• Common symptoms include squeaking or grinding, door rubbing or sagging, or the door not closing smoothly
• Physical signs include cracks, flattening, or oval-shaped wear in the bushing

• Unplug the refrigerator and remove items from the door
• Support the door; remove the top hinge cover and screws, then lift the door slightly
• Replace the worn upper hinge bearing on the hinge pin or bracket (design varies)
• Reinstall the hinge, align the door, and ensure proper gasket contact

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

Specs: Hex head ,1/4-20 x 5/8

This drive cam is the rotating plastic cam used in the refrigerator's ice system. It transfers the motor's motion to linked parts to advance the cycle so ice can be produced and dispensed smoothly.

• Transfers rotation from the motor to move internal levers/gears in the ice assembly
• Advances the ice-making/dispensing cycle
• Wear or cracks can cause stalling, clicking/grinding, or no/weak ice dispensing
• May lead to ice not ejecting or jamming mid-cycle

• Disconnect power and shut off water before servicing
• Remove the ice bin; access the ice maker or dispenser mechanism as your model requires
• Note the cam's orientation and alignment marks; seat the new cam fully on the shaft
• Reassemble, restore power, and run a test cycle to confirm operation

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is not a filter. Use this bypasss if don't want to use the PureSource 2 Water Filter WF2CB or the Pure Advantage Water Filter EWF2CBPA.

This refrigerator shelf restores a flat, sturdy surface for storing food and containers. Replace a broken or missing shelf to regain capacity, keep items organized, and help prevent spills inside your appliance.

• Provides a level platform to hold groceries and containers
• Helps organize contents and maximize usable space
• Replaces damaged, bent, or missing shelves
• Common symptoms: cracked/broken shelf, wobbling, items tipping, reduced storage capacity

• Empty the area and wear gloves; handle carefully to avoid injury or damage
• Align the shelf with the side supports and slide or lower it into place
• Ensure it's fully seated before loading; distribute weight evenly

This sliding basket replaces a damaged or missing freezer drawer basket to restore organized, pull-out storage and easier access to frozen items. It provides stable support for stored food and helps keep contents contained while sliding. What it does:

• Provides pull-out storage and organization for frozen foods.
• Restores drawer function when the original basket is cracked, broken, missing, or catches.
• Keeps items contained and easier to reach than loose stacking on shelves.
• Improves visibility and access to stored frozen goods.

• Always unplug the appliance and remove food/ice before starting any repair.
• Remove the old basket per the appliance service instructions and slide the replacement into the existing rails.
• Basic hand tools may be needed; retain original clips or fasteners if present.
• Verify fit by part number and appliance model before installation.