Glhs38 Parts

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a plastic actuator pad located behind the dispenser panel on a refrigerator door. When you press a glass against it, it triggers the water dispenser switch to start the flow of water. Replace this actuator if the water dispenser no longer responds to pressure, the paddle is cracked or broken, or if you have to press unusually hard to get water to dispense.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Freezer won't maintain temperature or cycles incorrectly? This thermistor sensor monitors temperature and signals the control board. DIY-friendly repair.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

If your crushed ice comes out in large chunks or clumps, this fixed blade may be worn or broken. Works with the auger to deliver consistent crushed ice.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Fridge not cooling or making loud buzzing noise? This compressor kit restores cooling in refrigerators and freezers. Professional repair recommended.

Right side.

Specs: 1.40`` long

This replacement extension support restores proper alignment and secure mounting for the appliance component it attaches to, helping stop misalignment, rubbing, or loose parts and letting the appliance operate smoothly. What it does:

• Replaces a worn, broken or missing extension support used to secure or extend a nearby panel, drawer, or assembly.
• Helps stop rattling, uneven movement, or binding caused by a damaged support piece.
• Restores proper spacing and mounting so associated parts track and close correctly.
• Works as a direct-fit replacement when the original extension is damaged or missing.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle edges carefully; use basic hand tools and keep original fasteners if reusing them.
• If mounting hardware is missing or damaged, source matching screws/clips separately.

A replacement PUR-BETA control module that restores control for the refrigerator's PUR water/dispense/filter functions so the dispenser, filter status and related signals operate properly. What it does:

• Manages electronic signals for the PUR filtration and dispenser circuitry
• Communicates filter status and reset information to the fridge control system
• Controls/coordinates water and dispenser-related functions tied to the PUR system
• Common symptoms of a failing module include unresponsive water/ice dispenser, persistent filter-status light, or intermittent dispenser operation

• Always disconnect power (and water supply when applicable) before servicing to avoid shock or water damage
• Handle the module carefully and avoid static discharge; use a grounded wrist strap if available
• Some panel removal and connector unplugging is required; keep track of screws and connectors

Black plastic cover that snaps over the top door hinge on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.