Glhs66ejsbo Parts

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This replacement ice container front is the front cover for the freezer's ice bucket. It restores a secure front wall so cubes stay contained and the bucket seats and dispenses correctly. What it does:

• Forms the front face of the ice container to keep ice contained
• Helps the bucket fit and align for proper dispensing
• Replaces a cracked, broken, loose, or missing front panel
• May help if ice spills from the bin or the bucket won't slide in or latch properly

• 1 ice container front (front cover only)

• Unplug the refrigerator and remove the ice bucket from the freezer
• Empty the bucket; transfer any screws, clips, or labels from the old front to the new part
• Align tabs and snap/fasten the new front to the bucket; do not overtighten screws
• Reinstall the bucket and check seating and dispenser operation

This is not a filter. Use this bypasss if don't want to use the PureSource 2 Water Filter WF2CB or the Pure Advantage Water Filter EWF2CBPA.

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This ice container deflector attaches to the ice bucket assembly and guides cubes toward the dispenser chute. Replacing a cracked or missing deflector restores proper ice flow and helps keep ice from spilling inside the freezer during dispensing.

• Directs ice from the bucket into the dispenser chute/crusher path
• Helps maintain consistent dispensing and minimizes stray ice inside the freezer
• Replace if cracked, warped, or missing
• Symptoms include erratic dispensing, ice spilling or jamming, or a visibly damaged/missing guide on the ice bin

• Disconnect power before servicing; remove the ice bucket
• Position the new deflector in the original location; reuse existing screws/clips if applicable
• Ensure the curved face points toward the dispenser chute
• Reinstall the ice bucket, restore power, and test ice dispense

Shroud assembly that covers internal refrigerator components and helps direct airflow for consistent cooling. Replacing a cracked or damaged shroud restores proper airflow paths and can reduce fan vibration and contact-related noise. What it does:

• Covers and protects internal components from debris and accidental contact.
• Directs airflow around the evaporator/fan area to support even cooling; symptoms of a failing shroud include uneven cooling or frost buildup.
• Reduces fan noise and vibration when mounting tabs or the housing are intact.
• Visible cracks, broken tabs, or holes are common signs the shroud needs replacement.

• Always disconnect power to the appliance before beginning any repair.
• Remove interior panels and fasteners carefully; retain hardware for reinstallation.
• Align tabs and mounting points; do not force broken tabs—replace damaged fasteners as needed.

This is a factory replacement screw fastener used to secure components in your appliance. It restores a tight, rattle-free fit for panels, brackets, and trim when an original screw is missing, stripped, or corroded.

• Secures panels, brackets, and trim to the appliance cabinet or liner
• Replaces a missing, stripped, or rusty screw
• Helps eliminate looseness, vibration, or rattling components
• Maintains proper alignment and a clean, factory fit

• Unplug the appliance before servicing; if near water lines, shut off the supply
• Match to the original and install in the same location/orientation
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Keep and reuse any original washers or spacers if present

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This replacement screw secures designated components in your appliance to maintain a tight, rattle-free fit. Replacing missing or stripped hardware restores proper attachment and helps keep panels and trim properly aligned.

• Fastens specified parts to the cabinet or frame
• Helps maintain alignment of panels and trim pieces
• Replaces missing, stripped, or corroded screws
• Common symptoms: loose or vibrating parts, panel/trim won't stay secured, visible missing hardware

• Disconnect power to the appliance before servicing
• Hand-start threads to avoid cross-threading; use the correct driver
• Do not overtighten, especially when threading into plastic
• If replacing multiple screws, replace one at a time to maintain alignment

This freezer thermistor is the sensor that reports compartment temperature to the control system. Replacing a faulty sensor restores accurate temperature feedback and normal cycling so the freezer maintains consistent, food-safe temperatures.

• Monitors freezer temperature and sends a resistance signal to the control
• Helps regulate compressor and evaporator fan operation for stable cooling
• Failure can cause temperatures that are too warm or too cold
• May lead to long run times, short cycling, or erratic temperature displays/alarms

• Disconnect power before servicing
• Access the sensor in the freezer and note its original routing and position
• Install the new sensor in the same location; route wires along the factory path and ensure a secure connection
• Restore power and allow up to 24 hours for temperatures to stabilize

This fixed blade sits inside the refrigerator's ice bucket/crusher assembly. It provides a stationary cutting edge that works with the auger and rotating blades to break up cubes, helping your dispenser deliver consistent crushed ice.

• Stationary crusher blade that works with the auger and rotating blades to crush ice
• Helps prevent whole cubes from passing through on the "crushed" setting
• Worn, bent, or missing blades can cause poor crushing, jams, or uneven ice size
• May help address symptoms like dispenser jamming, irregular crushed ice, or increased grinding noises

• Unplug the refrigerator before servicing; remove and empty the ice bucket
• Note the order and orientation of blades, spacers, and fasteners; take reference photos
• Handle sharp metal edges; wear cut-resistant gloves
• Reassemble in the original sequence and tighten hardware snugly; ensure the auger turns freely before reinstalling

This small but critical actuator spring restores return tension in a refrigerator's actuator mechanism, helping the lever reset to neutral after use so controls feel responsive and operation stops cleanly. What it does:

• Provides the return force for an actuator or lever so it moves back to its neutral position
• Helps the mechanism engage/disengage a switch cleanly
• Common symptoms of a weak or broken spring: lever sticks, feels loose, or doesn't spring back
• Contribute to intermittent activation or failure to stop when released

• 1 actuator spring

• Disconnect power; if working near the dispenser/water system, shut off the water supply
• Access the actuator mechanism and note the spring's exact orientation (take a photo before removal)
• Use needle-nose pliers to transfer the spring; do not over-stretch or deform it
• Wear cut-resistant gloves and eye protection; test lever return action before reassembly

Color: White

Specs: 1.40`` long