Glw2800d1ws Parts

Timer knob for washer control panel. Replace this graphite-silver dial if cracked, broken, or missing. Easily installs on control panel shaft.

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a small connector jumper wire used in the washer's control system to select the correct operating model or configuration. It plugs into the control board or wiring harness to ensure the washer runs the proper cycle programming for your specific unit. Replace this connector if your washer is not responding to cycle selections correctly or if the original connector is missing or damaged.

Flood hose for top-load washers. Connects tub to base to drain overflow water. Replace if cracked, leaking, or gasket is worn or damaged.

A foam insulation barrier that helps seal and protect refrigerator cabinet cavities from air and moisture intrusion. Replaces worn or damaged foam to support proper airflow and reduce the risk of frost buildup around internal components. What it does:

• Provides an insulating seal between cabinet panels and service openings
• Helps limit warm air ingress that can cause frost or reduced cooling performance
• Cushions and isolates components to reduce vibration noise
• Restores original fit where foam has deteriorated or been removed during repairs

• Disconnect power to the appliance before starting any repair
• Remove surrounding panels as needed to access the foam location
• Clean and dry mounting surfaces before applying; use adhesive if required by OEM instructions
• Avoid compressing or blocking vents and airflow paths during installation

Washer won't spin or agitate? This lid switch assembly detects if the lid is closed. Moderate DIY repair—front panel removal required. Video available.

Fix a washer that won't advance through cycles or skips fill/agitate steps. This timer controls cycle sequencing. DIY repair in about 30 minutes.

Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.

Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.

Power line filter sits between household AC and washer's internal wiring. Replace when cracked, corroded, or causing breaker trips due to electrical noise.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.