Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.
Removed some screws, opened the top of the wash machine, unplugged some wires to remove the part, plugged the wires back into the mew part, put the new water valve into place, secured the water valve with the screw, put the top back on the wash machine, and replaced all remaining screws! Real Simple! Read more
This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.
Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.
I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.
Googled the problem, watched videos on Youtube. Took apart machine and tried cleaning filter most people said was the problem. Wasn't anything but a penny in it so that wasn't the problem. I decided the pump must be bad ,the spring for the bellows and the console were broken so I bought those as well. Got the parts put them on and machine filled up with water turned over a few times and then stopped. The only thing else it could be is the fill level sensor or the main circuit board. Ordered... Read more
Replacement mounting screw that fastens panels and components in laundry centers. Needed when original is missing, stripped, or damaged to restore secure fit.
Read your terms & conditions thanks for having parts available Read more
Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.
The repair guy told me if I have him fix it I should just buy a new one. I like my washer and dryer because it's a combo and takes up little space so I decided to fix it myself. Not sure if I got lucky but appliance parts pros had a video with almost my exact washer which made repair very easy. Read more
Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.
It was easier than I imagined! I watched a video on youtube...I wish they would put up fixit videos on this site. There isn't much to a dryer...:-> Read more
This is a short coil spring that connects the outer wash tub to the washer cabinet, helping absorb vibration and support the tub during spin cycles. It works alongside other suspension springs to keep the tub balanced and reduce excessive movement. Replace this spring if the washer shakes or bangs excessively during spin, the tub hangs unevenly, or you notice a broken or stretched spring during inspection.
This is a small spring that attaches to the lid of a laundry center washer, providing tension to hold the lid in position. It helps the lid stay open during loading and close securely during operation. Replace this spring if your washer lid won't stay open, slams shut on its own, or the original spring is broken or stretched out.
Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.
It took less than 5 minutes to fix it. It was very simple, the part fit perfect. I will keep this web site in my favorites for later use. Read more
Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.
This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.
This is a small metal or plastic retainer clip that secures the main top panel of the dryer to the cabinet frame. It holds the top panel firmly in place so it doesn't shift or rattle during operation. If your dryer's top panel feels loose, pops up during use, or won't stay properly seated, this clip may be broken or missing.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.