Gmc275pdb6pds07 Parts

The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more

I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more

I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more

I have a 10 year old Kitchenaid double oven with warming drawer below and electrical connection is located in cabinet below. I order a service manual from http://www.allrepairmanuals.com. If you have the service manual follow it, it walks a technician thru each step. If you don't have a manual here are a few highlights. Disclaimer the following is for my oven model KEBS208DBL8, your oven service steps may vary. IMPORTANT! First step turn-off the power to the oven (mine was a 40 amp breaker)... Read more

Replaced the magnetron, capacitor and diode. Symptoms of failure were change in tone/noise put out by the microwave and no heat in the item being microwaved. Could have been a failure of either the diode, capacitor or the magnetron, but I believe it was the magnetron that failed. Replaced all three. The right hand side of the housing needs to be removed to access these parts. Take lots of pictures for reference as it all comes apart, wiring, placement of the various screws, etc. Not an easy... Read more

Ordered the right screw and screwed it in. Door now properly secured. Read more

I purchased a can of black appliance spray paint, removed the panels on the dishwasher, sprayed them, and a few hours later put them back. They're beautiful and it looks like I have a brand new dishwasher! It now matches everything and looks great with the new granite counter tops I just installed. THANK YOU FOR THE GREAT IDEA!!! I'm a 76 year old female and my friends think I'm a genius! Read more

A you tube video helped in removing the oven door. After removing the screws, though, the top did not separate. Since I could lift the bottom up enough to get the old door hinges out and put the new ones in, I closed it back and put the screws back in. There was an issue in screw in two of the screws on the bottom of the door. They would not screw all the way in and are about 1/8 inch out. I checked the depth of the hole and it appears to be blocked about 1/2 inch down, although that... Read more

I measured the resistance between the two connectors on the magnetron: should be close to zero ohms and it was. I measured between the same connectors and the metal case: should be mega ohms, it was 15k ohms. That is a bad, partly shorted unit. I also checked the resistance of the thermal cut off, which should be zero but was 10 ohms so I replaced. The HV diode is checked with a 9 V battery (YouTube checking microwave HV diode) and it too was bad. Make sure to take pictures as you disassemble... Read more

Ordered a new left side hinge from appliancepartspros.com and it arrived overnight although I paid for standard shipping only. Replaced the left side hinge which was visibly misshapen and damaged. Followed video instructions on U-tube to remove the oven door and hinge, installed new hinge, reassembled and re-installed door. It works like a champ now! About a 45 minute repair and I work slowly. Read more

Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more