Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.
I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more
Replacement right-hand oven door hinge that provides the pivot point and spring tension for smooth opening and closing. Install when bent or worn.
The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more
Black control panel assembly that forms the front interface surface for your oven. Replace if cracked, broken, or mounting tabs are damaged or missing.
I replaced the control board without much difficulty, but found original installer had broken all but one of the plastic screw receptacles embedded in the control panel cover. They had originally super-glued the plastic to the wall! Anyway, ordered the plastic control panel frame and stainless cover (our cover had been dented previously). Installation was easy, just know that after you unscrew the four retaining screws (2 on each side of control panel) you must LIFT the panel up off the... Read more
Replace your oven's left-hand door hinge to restore smooth opening and a proper seal. Fixes doors that won't close, sag, or have weak springs. Confirm fit.
This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:
I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more
Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.
Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more
Microwave not heating? This high voltage capacitor works with the magnetron and diode to generate heat. Moderate DIY repair with proper safety precautions.
Replaced the magnetron, capacitor and diode. Symptoms of failure were change in tone/noise put out by the microwave and no heat in the item being microwaved. Could have been a failure of either the diode, capacitor or the magnetron, but I believe it was the magnetron that failed. Replaced all three. The right hand side of the housing needs to be removed to access these parts. Take lots of pictures for reference as it all comes apart, wiring, placement of the various screws, etc. Not an easy... Read more
This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.
The oven temperature was low and the heating time excessive. However, the range display showed the requested 400F, even though the oven was really 250F. Because the oven displayed an inaccurate temperature, I ordered an oven sensor, a heating element, and a terminal block. Replacing the heating element fixed the problem. The element I received was the same shape and size, but the supports were not the same. However, I think it must have been a design change after mine was manufactured... Read more
Screw for control panel vent.
Ordered the right screw and screwed it in. Door now properly secured. Read more
Protects your oven's electronic control by absorbing voltage spikes and filtering electrical noise. Replace if burnt or after power surges cause control issues.
Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.
Ordered the two hinges, removed the oven door and replaced the hinges. Read more
This replacement transformer steps down household 120VAC, 60Hz power to the low voltage used by the appliance's electronic control. Replacing a failed transformer can restore power to the display/clock and control circuits so cooking functions respond properly. What it does:
Replaced power transformer. I used a multimeter to measure output voltage of the transformer and discovered there was no output voltage. It would have helped a great deal if I had an electrical schematic and wiring diagram. The component identification drawings where helpful to locat components. Read more
Replace your cracked, dented, or worn 30-inch oven door panel. This outer skin restores appearance and supports the handle, glass, and trim assembly.
If your oven control flickers or resets randomly, the transient suppressor may have failed. This part protects the control board from power surges.
Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.
Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more
Left-side oven door hinge for electric wall ovens and ranges. Replaces broken, bent, or worn hinges that prevent door removal or proper closing.
The little flip-over locks on my oven door hinges were bent and broken, preventing me from removing the oven door. It took a little bit of searching to determine that my oven purchased from Ikea was actually built by Whirlpool, and finally what were the correct part numbers for both hinges. Much to the credit of AppliancePartsPros.com, they were the only site that specifically labeled these hinges as Left and Right which helped greatly - even the parts diagrams from Whirlpool were not... Read more