Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If your range has a strong burning smell or won't power on, the terminal block may be heat-damaged. This insulated connector restores safe power flow.
Replaced it with the part I got from you. Read more
If your oven door won't lock, stays locked after self-clean, or shows door lock errors, this door lock motor and switch assembly often solves the issue.
My appliance is a Whirlpool Accubake Wall Oven, single door. After using the tech sheet and measuring the ohms of the two micro switches that sends signals when the door is shut and locked, determined the lock was faulty. Pretty simple to change, the most difficult part was taking the digital face off of the oven without damaging the control board. TIP: take a picture of the latch switches to ensure you put the correct wires on the correct switch. Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
This ground screw secures the appliance's grounding wire or strap to the chassis or terminal area, creating a reliable bonding point. Replace a missing or damaged screw to restore a proper ground connection during installation or service.
New hinges solved the problem! FYI the mounting holes were not tapped for screws, I was able to self tap but glad I bought new screws. Read more
Black control panel assembly that forms the front interface surface for your oven. Replace if cracked, broken, or mounting tabs are damaged or missing.
I replaced the control board without much difficulty, but found original installer had broken all but one of the plastic screw receptacles embedded in the control panel cover. They had originally super-glued the plastic to the wall! Anyway, ordered the plastic control panel frame and stainless cover (our cover had been dented previously). Installation was easy, just know that after you unscrew the four retaining screws (2 on each side of control panel) you must LIFT the panel up off the... Read more
Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.
I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more
Door hinge receiver for wall ovens. Mounts inside the oven frame to hold the door hinge in place. Replace if cracked, deformed, or causing door alignment issues.
This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:
I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more
Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.
Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more
Kit of 4 pins that insert into oven door hinges to safely remove the door for repairs or cleaning. Replace lost or damaged pins during door removal.
I have a 10 year old Kitchenaid double oven with warming drawer below and electrical connection is located in cabinet below. I order a service manual from http://www.allrepairmanuals.com. If you have the service manual follow it, it walks a technician thru each step. If you don't have a manual here are a few highlights. Disclaimer the following is for my oven model KEBS208DBL8, your oven service steps may vary. IMPORTANT! First step turn-off the power to the oven (mine was a 40 amp breaker)... Read more
Microwave not heating? This high voltage capacitor works with the magnetron and diode to generate heat. Moderate DIY repair with proper safety precautions.
Replaced myself. Read more
Protects your oven's electronic control by absorbing voltage spikes and filtering electrical noise. Replace if burnt or after power surges cause control issues.
Screw for control panel vent.
Ordered the right screw and screwed it in. Door now properly secured. Read more
This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.
The oven temperature was low and the heating time excessive. However, the range display showed the requested 400F, even though the oven was really 250F. Because the oven displayed an inaccurate temperature, I ordered an oven sensor, a heating element, and a terminal block. Replacing the heating element fixed the problem. The element I received was the same shape and size, but the supports were not the same. However, I think it must have been a design change after mine was manufactured... Read more
Replace your cracked, dented, or worn 30-inch oven door panel. This outer skin restores appearance and supports the handle, glass, and trim assembly.
Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.
Ordered the two hinges, removed the oven door and replaced the hinges. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.