Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement right-hand oven door hinge that provides the pivot point and spring tension for smooth opening and closing. Install when bent or worn.
The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more
Replace your oven's left-hand door hinge to restore smooth opening and a proper seal. Fixes doors that won't close, sag, or have weak springs. Confirm fit.
Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.
I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more
Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.
Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more
This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:
I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more
Door hinge receiver for wall ovens. Mounts inside the oven frame to hold the door hinge in place. Replace if cracked, deformed, or causing door alignment issues.
This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.
What's included: One 10-32 nut Install notes:
The oven temperature was low and the heating time excessive. However, the range display showed the requested 400F, even though the oven was really 250F. Because the oven displayed an inaccurate temperature, I ordered an oven sensor, a heating element, and a terminal block. Replacing the heating element fixed the problem. The element I received was the same shape and size, but the supports were not the same. However, I think it must have been a design change after mine was manufactured... Read more
Kit of 4 pins that insert into oven door hinges to safely remove the door for repairs or cleaning. Replace lost or damaged pins during door removal.
I have a 10 year old Kitchenaid double oven with warming drawer below and electrical connection is located in cabinet below. I order a service manual from http://www.allrepairmanuals.com. If you have the service manual follow it, it walks a technician thru each step. If you don't have a manual here are a few highlights. Disclaimer the following is for my oven model KEBS208DBL8, your oven service steps may vary. IMPORTANT! First step turn-off the power to the oven (mine was a 40 amp breaker)... Read more
Microwave not heating? This high voltage capacitor works with the magnetron and diode to generate heat. Moderate DIY repair with proper safety precautions.
Replaced the magnetron, capacitor and diode. Symptoms of failure were change in tone/noise put out by the microwave and no heat in the item being microwaved. Could have been a failure of either the diode, capacitor or the magnetron, but I believe it was the magnetron that failed. Replaced all three. The right hand side of the housing needs to be removed to access these parts. Take lots of pictures for reference as it all comes apart, wiring, placement of the various screws, etc. Not an easy... Read more
Protects your oven's electronic control by absorbing voltage spikes and filtering electrical noise. Replace if burnt or after power surges cause control issues.
Screw for control panel vent.
Ordered the right screw and screwed it in. Door now properly secured. Read more
Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.
Ordered the two hinges, removed the oven door and replaced the hinges. Read more
Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.
I purchased a can of black appliance spray paint, removed the panels on the dishwasher, sprayed them, and a few hours later put them back. They're beautiful and it looks like I have a brand new dishwasher! It now matches everything and looks great with the new granite counter tops I just installed. THANK YOU FOR THE GREAT IDEA!!! I'm a 76 year old female and my friends think I'm a genius! Read more
If your oven control flickers or resets randomly, the transient suppressor may have failed. This part protects the control board from power surges.
This fixed thermostat protects the appliance by opening the circuit when excessive heat is detected. Replacing a failed or weak thermostat restores reliable over-temperature protection and helps prevent heat-related shutdowns.
I measured the resistance between the two connectors on the magnetron: should be close to zero ohms and it was. I measured between the same connectors and the metal case: should be mega ohms, it was 15k ohms. That is a bad, partly shorted unit. I also checked the resistance of the thermal cut off, which should be zero but was 10 ohms so I replaced. The HV diode is checked with a 9 V battery (YouTube checking microwave HV diode) and it too was bad. Make sure to take pictures as you disassemble... Read more
This block-style fuse holder secures and connects the appliance fuse to the wiring harness, restoring a safe electrical connection and thermal protection. Use it when the original fuse block is cracked, corroded, or no longer holding the fuse securely. What it does:
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.