Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Black control panel assembly that forms the front interface surface for your oven. Replace if cracked, broken, or mounting tabs are damaged or missing.
I replaced the control board without much difficulty, but found original installer had broken all but one of the plastic screw receptacles embedded in the control panel cover. They had originally super-glued the plastic to the wall! Anyway, ordered the plastic control panel frame and stainless cover (our cover had been dented previously). Installation was easy, just know that after you unscrew the four retaining screws (2 on each side of control panel) you must LIFT the panel up off the... Read more
Replace your oven's left-hand door hinge to restore smooth opening and a proper seal. Fixes doors that won't close, sag, or have weak springs. Confirm fit.
The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more
Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.
Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more
This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:
I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more
Microwave not heating? This high voltage capacitor works with the magnetron and diode to generate heat. Moderate DIY repair with proper safety precautions.
Replaced the magnetron, capacitor and diode. Symptoms of failure were change in tone/noise put out by the microwave and no heat in the item being microwaved. Could have been a failure of either the diode, capacitor or the magnetron, but I believe it was the magnetron that failed. Replaced all three. The right hand side of the housing needs to be removed to access these parts. Take lots of pictures for reference as it all comes apart, wiring, placement of the various screws, etc. Not an easy... Read more
This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.
The oven temperature was low and the heating time excessive. However, the range display showed the requested 400F, even though the oven was really 250F. Because the oven displayed an inaccurate temperature, I ordered an oven sensor, a heating element, and a terminal block. Replacing the heating element fixed the problem. The element I received was the same shape and size, but the supports were not the same. However, I think it must have been a design change after mine was manufactured... Read more
Screw for control panel vent.
Ordered the right screw and screwed it in. Door now properly secured. Read more
Replace your cracked, dented, or worn 30-inch oven door panel. This outer skin restores appearance and supports the handle, glass, and trim assembly.
Oven won't heat or element burned out? This high-temperature cut-out fuse interrupts power when temperatures exceed safe levels. Often fails with elements.
We bought both bottom elements for each oven. They installed and now work PERFECTLY! Thank you! Read more
Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.
Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more
Left-side oven door hinge for electric wall ovens and ranges. Replaces broken, bent, or worn hinges that prevent door removal or proper closing.
The little flip-over locks on my oven door hinges were bent and broken, preventing me from removing the oven door. It took a little bit of searching to determine that my oven purchased from Ikea was actually built by Whirlpool, and finally what were the correct part numbers for both hinges. Much to the credit of AppliancePartsPros.com, they were the only site that specifically labeled these hinges as Left and Right which helped greatly - even the parts diagrams from Whirlpool were not... Read more
This fixed thermostat protects the appliance by opening the circuit when excessive heat is detected. Replacing a failed or weak thermostat restores reliable over-temperature protection and helps prevent heat-related shutdowns.
I measured the resistance between the two connectors on the magnetron: should be close to zero ohms and it was. I measured between the same connectors and the metal case: should be mega ohms, it was 15k ohms. That is a bad, partly shorted unit. I also checked the resistance of the thermal cut off, which should be zero but was 10 ohms so I replaced. The HV diode is checked with a 9 V battery (YouTube checking microwave HV diode) and it too was bad. Make sure to take pictures as you disassemble... Read more
If your oven display is unreadable or buttons don't respond, this control panel assembly restores your console. Moderate DIY repair with careful disassembly.
Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.
I purchased a can of black appliance spray paint, removed the panels on the dishwasher, sprayed them, and a few hours later put them back. They're beautiful and it looks like I have a brand new dishwasher! It now matches everything and looks great with the new granite counter tops I just installed. THANK YOU FOR THE GREAT IDEA!!! I'm a 76 year old female and my friends think I'm a genius! Read more
The Thermal Fuse is an OEM component specifically designed for Whirlpool ovens. As an important safety device, it is located near heat-producing elements inside the oven cavity. Causes of a bad thermal fuse include overheating of elements or surrounding components over time, which can eventually blow the fuse. Symptoms of a faulty thermal fuse include:
This genuine OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore oven models as well.
Gas burners won't ignite or spark continuously? This spark module generates the high-voltage spark needed to light burners. DIY repair in 30-60 minutes.
I called AppliancePartsPros.com and, with the able assistance of their call taker, was quickly able to determine that the spark module had failed and they had a replacement in stock and it would be immediately shipped to me. It left Oklahoma City that day, via Fed Ex Ground, and was delivered the next day to my location north of Houston. That was excellent service and I will continue to use AppliancePartsPros.com for any future appliance repair needs. Read more