We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement mounting screw for securing panels, brackets, and components inside your appliance. Needed when original screws are stripped or missing.
White. 8-18 x 5/16 inch.
Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Needed when original screws are stripped, missing, or lost.
Replace your dishwasher's control knob if it's cracked, broken, missing, or worn. This knob installs on the front control panel to operate cycle settings.
Secures control or selector knobs on your dishwasher. Replace if the latch is broken, cracked, or missing, causing knobs to slip or pop off the panel.
Secure dishwasher hoses and prevent leaks with this clamp. Replace if loose, cracked, or causing water leaks. Verify fit with your model number.
The Dishwasher Door Cable is an OEM replacement part for GE dishwashers. It works with the door latch assembly to ensure secure closure of the dishwasher door. The cable is responsible for connecting the door handle mechanism to the latch, allowing users to easily open and close the door with a gentle pull or push. Note: It is recommended to replace both at the same time.
Symptoms of a bad door cable include:
Causes of a bad cable can be frequent use that results in wear and fatigue of the internal wiring over time. Damage from harsh detergents or excess moisture can also compromise the cable.
This OEM GE replacement part is compatible with models from Hotpoint, RCA, and some Kenmore dishwashers as well.
First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more
Usually ships within 4 - 14 days
Replacement door vent directs humid air out during the dry cycle. Install inside the door panel to replace a cracked, clogged, or missing vent.
Found AppliancePartsPros.com and looked up parts and ordered replacement parts. ( VERY easy!) Replaced the spray arm assembly and door vent via the handy Q&A repair section, as well as a thorough cleaning, and VOILA! Clean dishes again!! Thanks for making it easy! Read more
Fix a dishwasher that won't drain or leaves dishes dirty. This impeller and seal kit restores water circulation when the pump is weak or noisy. Moderate DIY.
I replaced the Spray arm and the filter, checked under the appliance for a leaking seal and found it dry. took the cover off of the drain and cleaned it out. I also ran the dishwasher with about a cup of bleach in it to sanitize it. Read more
Connects dishwasher wiring to the water inlet valve. Replace if the plug is burnt, brittle, loose, or corroded to restore a secure electrical connection.
Dishwasher had begun going through the cycles with not enough water in the chamber. Suspect was the water inlet valve. Checked the AppliancePartsPros video for this repair and ordered the valve from them. It arrived in a timely manner -as usual- and I pulled the dishwasher out, removed the kick toe cover, then the structural brace behind it then removed the valve. Installed the new valve, replaced the bracket and the toe cover and dish washer is back in service like brand new. Wife was ready to... Read more
Fix dishwasher leaks or poor cleaning with a new sump cap. Seals the sump opening to contain wash water and protect the pump. Quick DIY replacement.
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more
Size: 8-16 x 2 inch ss.
Replacement bracket that secures the flood switch in your dishwasher. Holds the leak detection switch in proper position. Needed when bracket is cracked or broken.