Gsd336onooss Parts

This CSM module assembly is the control sub-module that manages tub functions on compatible GE top-load washers, restoring normal cycle control and communication between the console and tub components. What it does:

• Controls and coordinates tub operations including agitation, spin, and cycle sequencing
• Helps the washer register and execute user-selected wash cycles
• Addresses symptoms such as washer not starting cycles, intermittent or no agitation/spin, or error codes related to tub control
• Works with the washer's main control and sensors to ensure proper cycle timing and transitions

• 1 CSM module assembly (C-Tub)

• Disconnect power to the appliance before beginning any work to avoid electrical shock
• Access typically requires removing the washer cabinet or console; handle the module and connectors gently
• Verify connector orientation and secure all wiring before restoring power

This outer door panel replaces a damaged or dented exterior door surface to restore appearance and protect inner door components. The stainless steel finish provides a clean look and resists everyday wear. What it does:

• Covers and protects the dishwasher/dryer/washer door assembly from impact and cosmetic damage
• Restores a uniform stainless finish to improve appliance appearance
• Helps keep internal door components free from moisture and debris
• Addresses symptoms such as dents, deep scratches, peeling finish, or visible corrosion on the outer door

• One outer door panel (stainless steel)

• Designed as a direct-fit replacement; follow your model's service manual for disassembly and reassembly steps
• Turn off power and water to the appliance before beginning service
• Use proper tools and support the door during removal to avoid dropping or bending the panel
• If clips or fasteners show damage, replace them; only install items explicitly shown as included

This SCR (silicon-controlled rectifier) is a control-circuit power-regulation component that helps manage electrical flow to appliance subsystems for reliable operation and stable control response. What it does:

• Regulates power flow in an appliance's electronic control circuit for proper component operation
• Helps enable consistent motor, heater, or timing control where used on the control board
• Faulty SCRs can cause intermittent operation, failure to start, or erratic control behavior
• Replacing a damaged SCR can restore steady, predictable appliance function

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle as an electronic/ESD-sensitive component; use proper grounding and avoid static discharge
• Some installations require soldering or board-level replacement—inspect mounting and connections carefully

This cap seals the washer sump area to help prevent leaks and keep water contained during cycles. It replaces a worn or damaged sump cap to restore a watertight seal and normal draining. What it does:

• Covers and seals the sump opening to prevent water from leaking out of the pump/sump area
• Helps maintain proper drainage by keeping contaminants out of the sump cavity
• Common part to replace when you see water pooling under the washer or around the base
• Fits the sump/pump assembly area and works with existing seals and hoses

• One cap sump

• Disconnect power and water before starting any repair
• Access usually requires removing the washer's lower access panel or front panel; follow your model's service manual
• Inspect nearby seals, hoses and the pump for wear; replace any damaged components to prevent repeat leaks

This timer cover is the replacement trim that surrounds and protects the dryer or washer control timer on the control panel, restoring a finished look and shielding the timer mechanism from dust and debris. What it does:

• Replaces a cracked, faded, or damaged timer trim to improve appearance and protect the underlying timer assembly
• Helps keep lint, dust, and moisture away from the timer control area
• Restores correct alignment and mounting for the timer knob and control components
• Useful when the existing cover is loose, broken, or missing

• One timer cover

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the control panel or access bezel per your model's service instructions to reach the timer cover
• Use appropriate hand tools (screwdriver) and avoid forcing plastic tabs to prevent breakage

A shield switch that helps prevent oven/range operation when the door is open and ensures safe control behavior. Replaces a worn or failed interlock switch to restore normal start and door-safety responses. What it does:

• Acts as an interlock micro switch to detect door/cover position and block operation when open
• Commonly replaces a switch causing the control to not start or to behave intermittently
• Can resolve issues like no power to heating elements, control not responding, or oven not entering bake/lock modes
• Small electrical switch that completes or breaks the circuit based on door/cover position

• Disconnect power to the appliance before servicing to avoid shock or injury
• Replace the switch with the same part orientation and secure all connectors firmly
• Verify correct operation by restoring power and testing door open/close and normal cycle starts

This left-side door arm hinge secures and guides the appliance door, restoring proper alignment and smooth opening/closing. It replaces a bent or broken hinge to reduce sagging and uneven door movement. What it does:

• Supports the door on the left side and helps control its travel and position
• Restores proper door alignment when a hinge is bent, worn, or broken
• Helps eliminate door sagging, scraping, or uneven closing
• Works with existing hinge pins and mounting points to stabilize the door

• One left-side arm hinge

• Installation requires basic hand tools; refer to your model's service manual for step-by-step instructions
• Disconnect power (and water for washers) before starting any repair
• Inspect adjacent hinge hardware and fasteners; replace if worn to ensure proper fit and function

This right-hand arm hinge secures and guides the appliance door or access panel for proper alignment and smooth operation. It replaces a worn or broken hinge to restore correct door movement and positioning. What it does:

• Attaches the door to the cabinet and provides a pivot point for opening and closing
• Keeps the door aligned to prevent sagging, gaps, or rubbing
• Restores smooth, consistent door motion when the original hinge is bent, worn, or broken
• Helps reduce stress on the door and adjacent components caused by misalignment

• Install with power disconnected and appliance stable to avoid injury
• Tighten mounting fasteners securely but avoid over-torquing to prevent damage
• If replacing both sides or multiple components, inspect companion hinge and fasteners for wear

Replace a damaged upper/top dishrack to keep cups, glasses, and bowls secure and organized on the top level of your dishwasher. Restore smooth loading and dependable support when the original rack is rusted, bent, or broken.

• Holds and organizes items on the dishwasher's upper level
• Slides on the rail system for easy loading and unloading
• Helps prevent items from tipping during the wash cycle
• Replaces a rack that is rusted, deformed, or has broken/missing tines

• Disconnect power and water supply before servicing for safety.
• Open the door, extend the rack, and release the rack stops/end caps per your model.
• Remove the old rack; transfer any removable accessories from the old rack if applicable.
• Set the new rack on the rails, reinstall the stops/end caps, and verify smooth travel.

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This impeller kit restores reliable water movement inside the dishwasher pump. A worn or damaged impeller can lead to weak circulation, louder operation, and poor wash results; replacing the kit helps return normal pressure and performance. What it does:

• Drives water flow through the pump during wash cycles
• Helps maintain proper wash pressure for effective cleaning
• Can reduce grinding or rattling noises from the pump area

• Includes 1 impeller kit

• Disconnect power and shut off water before servicing
• Access the pump/sump area and note the orientation of parts during disassembly
• Inspect the pump housing and any seals/O-rings; replace worn components per your model's service information
• After reassembly, run a short cycle to check for leaks and strong water movement

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This insulation toe kick is a replacement panel that fits the refrigerator base to help block drafts and protect internal components under the cabinet. It restores the factory barrier that supports temperature stability and efficient operation. What it does

• Replaces damaged or missing toe-kick insulation that lets cold air escape beneath the appliance
• Helps reduce drafts and minimize warm air intrusion into the refrigerator cavity
• Protects wiring and components located in the toe-kick area from dust and debris
• Can help prevent uneven cooling or frost buildup that results from compromised base insulation

• One insulation toe kick panel

• Disconnect power to the appliance before starting any service
• Remove the existing toe kick/board and fasteners, then position the replacement so mounting tabs align with factory slots
• Avoid compressing or tearing the insulation; maintain original fit for proper performance